BS IEC/TS 60034-20-2 - ROTATING ELECTRICAL MACHINES - PART 20-2: PERFORMANCE CHARACTERISTICS AND TESTING SPECIFICATIONS FOR BRUSHLESS PERMANENT MAGNET MOTORS

Available format(s)

Hardcopy , PDF

Language(s)

English

Publisher

British Standards Institution

1 Scope
2 Normative references
3 Terms and definitions
   3.1 Brushless Permanent Magnet motor (BPM)
   3.2 Environment/Temperature
   3.3 Motor shaft/torque-speed/power ratings
   3.4 Motor winding & voltage ratings
   3.5 Power dissipation
   3.6 Mechanical
4 Characteristic ratings of BPM motor
   4.1 Torque-speed & output shaft data
   4.2 Deleted
   4.3 Power loss dissipation
   4.4 Mechanical
   4.5 Options
   4.6 Rating plate
5 Interface of BPM motor to converter
   5.1 Torque ratings
   5.2 Voltage at motor terminals
   5.3 Common mode voltage
6 Testing
   6.1 Motor type (design verification) testing for
        catalogue data
   6.2 Routine (Production) testing
   6.3 Installation testing of motor
Annex A - Published data
   A.1 Motor manufacturer published data
   A.2 Drive module data required for BPM
   A.3 Application data required for sizing BPM
Annex B - Control block diagrams
   B.1 Motor control block diagram for K[t]
   B.2 Equivalent control block diagram for K[e]
   B.3 Equivalent control block diagram for drive, motor,
        load and servo
   B.4 Shaft voltage equivalent circuit
Annex C - Thermal management
   C.1 Power loss dissipation
   C.2 Winding time constants
Annex D - Feedback devices comparison
Annex E - Sizing a BPM motor
Annex F - Method for evaluating torque ripple of PDS

BS IEC/TS 60034-20-2

Committee	PEL/2
DocumentType	Draft
Pages	61
PublisherName	British Standards Institution
Status	Current

IEC 60034-9:2003+AMD1:2007 CSV	Rotating electrical machines - Part 9: Noise limits
IEC 60068-1:2013	Environmental testing - Part 1: General and guidance
IEC 60068-2-27:2008	Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC TS 60034-27:2006	Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines
ISO 1940-1:2003	Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances
ISO 281:2007	Rolling bearings Dynamic load ratings and rating life
IEC 60072-1:1991	Dimensions and output series for rotating electrical machines - Part 1: Frame numbers 56 to 400 and flange numbers 55 to 1080
IEC TS 60034-18-41:2006	Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters
IEC 60034-18-22:2000	Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Classification of changes and insulation component substitutions
ISO 8821:1989	Mechanical vibration Balancing Shaft and fitment key convention
IEC 60034-18-1:2010	Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
IEC 60034-8:2007+AMD1:2014 CSV	Rotating electrical machines - Part 8: Terminal markings anddirection of rotation
IEC TS 60034-25:2014	Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
IEC 60034-14:2003+AMD1:2007 CSV	Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity
IEC 60034-18-21:2012	Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification
IEC 60034-1:2017	Rotating electrical machines - Part 1: Rating and performance
IEC 60034-2:1972	Rotating electrical machines. Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles)
IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV	Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
IEC 60068-2-75:2014	Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests
IEC 60068-2-29:1987	Environmental testing. Part 2: Tests. Test Eb and guidance: Bump
IEC 60068-2-1:2007	Environmental testing - Part 2-1: Tests - Test A: Cold
IEC 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests