09/30192800 DC : 0

Superseded

View Superseded by

BS ISO 29262 - PRODUCTION EQUIPMENT FOR MICROSYSTEMS - INTERFACE BETWEEN GRIPPERS AND HANDLING SYSTEM

Available format(s)

Hardcopy , PDF

Superseded date

31-03-2011

Language(s)

English

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Interface definitions
   5.1 Coordinate System
   5.2 Layer 1: Mechanical interface
   5.3 Layer 2: Service interface
   5.4 Layer 3: Bus interface part
   5.5 Tolerances
   5.6 Load bearing capacities
   5.7 Designation
Annex A (normative) - Tests procedure for fixation interface
        [p][R]
Bibliography

Committee	MTE/1
DocumentType	Draft
Pages	26
PublisherName	British Standards Institution
Status	Superseded
SupersededBy	BS ISO 29262:2011

DIN 32564-1:2004-05	Production equipment for micro-systems - Terms and definitions - Part 1: General terms of micro-system technology
IEC 61784-1:2014	Industrial communication networks - Profiles - Part 1: Fieldbus profiles
DIN 509:2006-12	Technical drawings - Undercuts - Types and dimensions
EN 50295:1999	Low-voltage switchgear and controlgear - Controller and device interface systems - Actuator Sensor interface (AS-i)
ISO/IEC 24702:2006	Information technology Generic cabling Industrial premises
ISO 1101:2017	Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
IEEE 802.3-2012	IEEE Standard for Ethernet
TIA/EIA 568-2 : C2009 AMD 1 2016	COMMERCIAL BUILDING TELECOMMUNICATIONS CABLING STANDARD - PART 2: BALANCED TWISTED-PAIR TELECOMMUNICATIONS CABLING AND COMPONENTS STANDARDS
ISO/IEC 11801:2002	Information technology Generic cabling for customer premises
ISO 9409-2:2002	Manipulating industrial robots Mechanical interfaces Part 2: Shafts
IEC 62026-2:2008	Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i)
ISO 3650:1998	Geometrical Product Specifications (GPS) Length standards Gauge blocks
ISO 286-1:2010	Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO 9409-1:2004	Manipulating industrial robots — Mechanical interfaces — Part 1: Plates
ISO 286-2:2010	Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO/IEC 24740:2008	Information technology Responsive Link (RL)
ISO 9787:2013	Robots and robotic devices Coordinate systems and motion nomenclatures
IEC 61131-2:2017	Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests
EN 61140:2016	Protection against electric shock - Common aspects for installation and equipment
DIN 7154-1:1966-08	ISO-FITS FOR THE HOLE BASIS SYSTEM; TOLERANCE ZONES, DEVIATIONS
ISO 8734:1997	Parallel pins, of hardened steel and martensitic stainless steel (Dowel pins)
DIN 7154-2:1966-08	ISO-FITS FOR THE HOLE BASIC SYSTEM; TOLERANCES OF FIT (CLEARANCES AND INTERFERENCES)
IEC TR 60479-3:1998	Effects of current on human beings and livestock - Part 3: Effects of currents passing through the body of livestock
ISO 18265:2013	Metallic materials — Conversion of hardness values