Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • 10/30165662 DC : 0

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    BS ISO 13706 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AIRCOOLED HEAT EXCHANGERS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-01-2012

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General
    5 Proposals
    6 Documentation
    7 Design
    8 Materials
    9 Fabrication of tube bundle
    10 Inspection, examination and testing
    11 Preparation for shipment
    12 Supplemental requirements
    Annex A (informative) - Recommended practices
    Annex B (informative) - Checklist and data sheets
    Annex C (informative) - Winterization of air-cooled heat
            exchangers
    Annex D (informative) - Recommended procedure for airflow
            measurement of air-cooled heat exchangers
    Annex E (normative) - Measurement of noise from air-cooled
            heat exchangers
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PSE/17/-/6
    Document Type Draft
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 4183:1995 Belt drives — Classical and narrow V-belts — Grooved pulleys (system based on datum width)
    AISC M011 : 9ED 89 MANUAL OF STEEL CONSTRUCTION
    ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
    ISO 9563:2015 Belt drives Electrical conductivity of antistatic endless synchronous belts Characteristics and test method
    ISO 1081:1995 Belt drives V-belts and V-ribbed belts, and corresponding grooved pulleys Vocabulary
    ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
    ISO 281:2007 Rolling bearings Dynamic load ratings and rating life
    NACE SP 04 72 : 2015 METHODS AND CONTROLS TO PREVENT IN-SERVICE ENVIRONMENTAL CRACKING OF CARBON STEEL WELDMENTS IN CORROSIVE PETROLEUM REFINING ENVIRONMENTS
    ISO 2491:1974 Thin parallel keys and their corresponding keyways (Dimensions in millimetres)
    ISO 1459:1973 Metallic coatings — Protection against corrosion by hot dip galvanizing — Guiding principles
    ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
    ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
    AISC S302 : 1986 CODE OF STANDARD PRACTICE FOR STEEL BUILDINGS AND BRIDGES
    ISO 5287:2003 Belt drives Narrow V-belts for the automotive industry Fatigue test
    ISO 76:2006 Rolling bearings Static load ratings
    ISO 4184:1992 Belt drives — Classical and narrow V-belts — Lengths in datum system
    ISO 5290:2001 Belt drives Grooved pulleys for joined narrow V-belts Groove sections 9N/J, 15N/J and 25N/J (effective system)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more