Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

10/30228056 DC : 0

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Available format(s)

Hardcopy , PDF

Superseded date

31-08-2013

Language(s)

English

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Types of regulating devices
5 Constructional characteristics
6 Performance characteristics
7 Test methods
8 Marking, packaging, instructions
Annex A (normative) - Special requirements for devices
        fitted with pressure or flow rate operated
        safety functions
Annex B (normative) - Special requirements for devices
        fitted with a thermal shut off system
Annex C (normative) - Special requirements for devices
        under extreme temperature conditions
        (temperatures below -20 Degree C)
Annex D (normative) - Regulating devices for LPG
        cylinders to supply appliances installed in
        caravans and motor caravans or freshwater boats
Annex E (normative) - Complementary test requirements
        for non metallic thermoplastic or thermal setting
        materials used in the construction of devices
Annex F (normative) - Requirements for elastomeric
        reinforced diaphragms
Annex G (normative) - Inlet connections
Annex H (normative) - Outlet connections
Annex I (informative) - Test method for resistance to
        corrosion
Annex J (normative) - Method for measuring leaks at
        test pressures less than or equal to 16 bar
Annex K (normative) - Special requirements for low
        pressure fixed regulators fitted with two or
        three outlets for outdoor use
Annex L (normative) - Special requirements for regulators
        fitted with an inlet valve
Annex M (Normative) - Devices for LPG cylinders to supply
        appliances installed in seawater boats
Annex ZA (informative) - Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 90/396/EEC
Bibliography

BS EN 16129.

Committee
GSE/24
DocumentType
Draft
Pages
153
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

Standards Relationship
PREN 16129 : DRAFT 2010 Identical

EN 15202:2012 LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections
ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
EN ISO 180:2000/A2:2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013)
EN 10226-2:2005 Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
EN ISO 4892-3:2016 Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016)
ISO 565:1990 Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
EN 13878 : 2003 LEISURE ACCOMMODATION VEHICLES - TERMS AND DEFINITIONS
EN ISO 3166-1:2014 Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013)
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
ISO 180:2000 Plastics Determination of Izod impact strength
ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
IEC 60695-11-10:2013 Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
EN ISO 8434-1:2007/AC:2009 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 3166-1:2013 Codes for the representation of names of countries and their subdivisions Part 1: Country codes
EN 12420:2014 Copper and copper alloys - Forgings
EN 549:1994 Rubber materials for seals and diaphragms for gas appliances and gas equipment
EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
ISO 301:2006 Zinc alloy ingots intended for castings
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
ISO 178:2010 Plastics Determination of flexural properties
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
1990/396/EEC : 1990 COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS

View more information
$86.27
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more