16/30312922 DC : 0

Superseded

View Superseded by

BS ISO 18888 - GAS TURBINE COMBINED CYCLE POWER PLANTS THERMAL PERFORMANCE TESTS

Available format(s)

Hardcopy , PDF

Superseded date

31-10-2017

Language(s)

English

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test boundary
5 Symbols and units
6 Preparation for test
7 Execution of test
8 Calculation of results for absolute test
9 Part load tests
10 Calculation of results for comparative test
11 Test report
Annex A (informative) - Typical secondary
        variables
Annex B (informative) - Numerical examples of
        uncertainty calculation
Annex C (normative) - Procedure for power factor
        conversion
Bibliography

BS ISO 18888.

Committee	MCE/16
DocumentType	Draft
Pages	79
PublisherName	British Standards Institution
Status	Superseded
SupersededBy	BS ISO 18888:2017

ISO/IEC 17025:2005	General requirements for the competence of testing and calibration laboratories
ISO 10715:1997	Natural gas — Sampling guidelines
ISO 6976:2016	Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition
ISO 3675:1998	Crude petroleum and liquid petroleum products Laboratory determination of density Hydrometer method
ISO 12242:2012	Measurement of fluid flow in closed conduits Ultrasonic transit-time meters for liquid
ISO 3977-1:1997	Gas turbines — Procurement — Part 1: General introduction and definitions
ISO 11086:1996	Gas turbines — Vocabulary
ASTM D 4868 : 2017 : REDLINE	Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
ISO 3977-9:1999	Gas turbines Procurement Part 9: Reliability, availability, maintainability and safety
ISO 6975:1997	Natural gas — Extended analysis — Gas-chromatographic method
ISO 2533:1975	Standard Atmosphere
ISO 6974-3:2000	Natural gas Determination of composition with defined uncertainty by gas chromatography Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two packed columns
DIN 51900-1:2000-04	Determining the gross calorific value of solid and liquid fuels using the bomb calorimeter, and calculation of net calorific value - Part 1: General information
ISO 5167:1980	Measurement of fluid flow by means of orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full
ISO 12185:1996	Crude petroleum and petroleum products — Determination of density — Oscillating U-tube method
ISO 2314:2009	Gas turbines — Acceptance tests
ISO 6817:1992	Measurement of conductive liquid flow in closed conduits Method using electromagnetic flowmeters
IEC 60751:2008	Industrial platinum resistance thermometers and platinum temperature sensors
ISO 10790:2015	Measurement of fluid flow in closed conduits Guidance to the selection, installation and use of Coriolis flowmeters (mass flow, density and volume flow measurements)
ISO 6974-1:2012	Natural gas — Determination of composition and associated uncertainty by gas chromatography — Part 1: General guidelines and calculation of composition
ISO 17089-1:2010	Measurement of fluid flow in closed conduits - Ultrasonic meters for gas Part 1: Meters for custody transfer and allocation measurement
ISO 12213-2:2006	Natural gas Calculation of compression factor Part 2: Calculation using molar-composition analysis
ISO 20765-2:2015	Natural gas Calculation of thermodynamic properties Part 2: Single-phase properties (gas, liquid, and dense fluid) for extended ranges of application
ASTM D 1945 : 2014 : REDLINE	Standard Test Method for Analysis of Natural Gas by Gas Chromatography
ISO 20765-1:2005	Natural gas Calculation of thermodynamic properties Part 1: Gas phase properties for transmission and distribution applications