A-A-55563 Revision D:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
14-05-2021
English
13-08-2013
1. SCOPE
2. CLASSIFICATION/PART OR IDENTIFICATION NUMBER (PIN)
3. SALIENT CHARACTERISTICS
4. REGULATORY REQUIREMENTS
5. PRODUCT CONFORMANCE PROVISIONS
6. PACKAGING
7. NOTES
Specifies the general requirements for a family of metal card guides (hereafter referred to as card holders) intended for use to guide and hold circuit card assemblies into their installed positions.
This Commercial Item Description (CID) covers the general requirements for a family of metal card guides (hereafter referred to as card holders) intended for use to guide and hold circuit card assemblies into their installed positions. Card holders covered by this CID are for moderate heat transfer and vibration applications. Requirements for specific card holders are covered in the individual CID specification sheets. Card holders covered by this CID are intended for commercial/industrial applications.
DevelopmentNote |
Supersedes DSCC 85020 (G) and DSCC 85021 (C). (07/2004)
|
DocumentType |
Standard
|
Pages |
6
|
PublisherName |
US Military Specs/Standards/Handbooks
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
A-A-55563-30 Revision A:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, CENTER MOUNTING, WITH MULTIPLE MOUNTING HOLES, UNSUPPORTED, FOR CHASSIS OR SUPPORTED MOUNTING APPLICATIONS |
A-A-55563-4 Revision C:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, CLOSED ENDED, WITHOUT FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES |
A-A-55563-27 Revision A:2013 | Holder, Electrical Card, Metal Card Guide, Closed Ended, with 2 Mounting Holes, for use with Heat Sinks |
A-A-55563-17 Revision B:2017 | Holder, Electrical Card, Metal Card Guide, Low Profile, Open Ended, without Flared Entry, with 2 Mounting Holes |
A-A-55563-13 Revision C:2017 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITH FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES, WITH CONTROLLED INSIDE BEND RADIUS |
A-A-55563-7 Revision C:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, OPEN ENDED, WITH FLARED ENTRY, WITH 3 MOUNTING HOLES |
A-A-55563-19 Revision B:2017 | Holder, Electrical Card, Metal Card Guide, Low Profile, Open Ended, without Flared Entry, with 2 Mounting Holes, Short Length |
A-A-55563-9 Revision C:2017 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, CLOSED ENDED, WITH FLARED ENTRY, WITH 3 MOUNTING HOLES |
A-A-55563-10 Revision C:2017 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, CLOSED ENDED, WITHOUT FLARED ENTRY, WITH 3 MOUNTING HOLES |
A-A-55563-14 Revision C:2017 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITHOUT FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES, WITH CONTROLLED INSIDE BEND RADIUS |
A-A-55563-28 Revision A:2013 | Holder, Electrical Card, Metal Card Guide, Closed Ended, with 3 Mounting Holes, for use with Heat Sinks |
A-A-55563-18 Revision B:2017 | Holder, Electrical Card, Metal Card Guide, Low Profile, Open Ended, without Flared Entry, with 3 Mounting Holes |
A-A-55563-11 Revision D:2017 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITH FLARED ENTRY, WITH 3 OFFSET (SIDE) MOUNTING HOLES |
A-A-55563-5 Revision D:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITH FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES |
A-A-55563-1 Revision C:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, OPEN ENDED, WITH FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES |
A-A-55563-20 Revision B:2017 | Holder, Electrical Card, Metal Card Guide, Low Profile, Open Ended, with Flared Entry, with 2 Mounting Holes, Short Length |
A-A-55563-23 Revision A:2013 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, MEDIUM PROFILE, CENTER MOUNT, WITH FLARED ENTRY, WITH 2 MOUNTING HOLES |
A-A-55563-2 Revision C:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, OPEN ENDED, WITHOUT FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES |
A-A-55563-15 Revision C:2017 | Holder, Electrical Card, Metal Card Guide, Low Profile, Open Ended, with Flared Entry, with 3 Mounting Holes, with Controlled Inside Bend Radius |
A-A-55563-25 Revision A:2013 | Holder, Electrical Card, Metal Card Guide, Open Ended, with 2 Mounting Holes, for use with Heat Sinks |
A-A-55563-16 Revision C:2017 | Holder, Electrical Card, Metal Card Guide, Low Profile, Open Ended, without Flared Entry, with 3 Mounting Holes, with Controlled Inside Bend Radius |
A-A-55563-21 Revision B:2018 | Holder, Electrical Card, Metal Card Guide, Low Profile, Closed Ended, without Flared Entry, with Three Mounting Holes, for Versamodule Eurocard Applications |
A-A-55563-29 Revision A:2013 | Holder, Electrical Card, Metal Card Guide, Narrow Profile, Center Mount, with Flared Entry, with 2 Mounting Holes |
A-A-55563-6 Revision D:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITHOUT FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES |
A-A-55563-22 Revision B:2018 | Holder, Electrical Card, Metal Card Guide, Low Profile, Closed Ended, with Flared Entry, with Three Mounting Holes, for Versamodule Eurocard Applications |
A-A-55563-26 Revision A:2013 | Holder, Electrical Card, Metal Card Guide, Open Ended, with 3 Mounting Holes, for use with Heat Sinks |
A-A-55563-8 Revision C:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, OPEN ENDED, WITHOUT FLARED ENTRY, WITH 3 MOUNTING HOLES |
A-A-55563-3 Revision C:2016 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, CLOSED ENDED, WITH FLARED ENTRY, WITH 2 OFFSET (SIDE) MOUNTING HOLES |
A-A-55563-12 Revision D:2017 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, LOW PROFILE, OPEN ENDED, WITHOUT FLARED ENTRY, WITH 3 OFFSET (SIDE) MOUNTING HOLES |
MIL-HDBK-1861 Revision B:2013 | Selection and Use1 of Electrical and Electronic Assemblies, Boards, Cards, and Associated Hardware |
A-A-55563-24 Revision A:2013 | HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, MEDIUM PROFILE, CENTER MOUNT, WITH FLARED ENTRY, WITH 3 MOUNTING HOLES |
SAE AMS 5906 : 2006 | STEEL, CORROSION-RESISTANT, SHEET AND STRIP, 18CR - 9.0NI (SAE 30302), COLD ROLLED, FULL HARD, 185 KSI (1276 MPA) TENSILE STRENGTH |
SAE AMS 2404 : 2013 | PLATING, ELECTROLESS NICKEL |
SAE AMS 5519 : 2014 | STEEL, CORROSION RESISTANT, SHEET AND STRIP, 18CR - 8NI (SAE 30301) COLD ROLLED, 185 KSI (1276 MPA) TENSILE STRENGTH |
ASTM B 733 : 2015 : REDLINE | Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal |
SAE AMS QQ P 416 : 2016 | PLATING, CADMIUM (ELECTRODEPOSITED) |
SAE AMS 5517 : 2000 | STEEL, CORROSION RESISTANT, SHEET AND STRIP, 18CR - 8NI (301) COLD ROLLED, 125 KSI (862 MPA) TENSILE STRENGTH |
ASTM A 684/A684M : 2017 : REDLINE | Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled |
SAE AMS QQ N 290 : 2015 | NICKEL PLATING (ELECTRODEPOSITED) |
SAE AMS 2418 : 2017 | PLATING, COPPER |
MIL-F-495 Revision E:1988 | FINISH CHEMICAL, BLACK FOR COPPER ALLOYS |
ASTM B 103/B103M : 2015 : REDLINE | Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar |
ASTM B 194 : 2015 : REDLINE | Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar |
SAE AMS 2700E : 2011 | PASSIVATION OF CORROSION RESISTANT STEELS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.