Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • ANSI/AWWA C903:2016

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    POLYETHYLENE-ALUMINUM-POLYETHYLENE (PEALPE) COMPOSITE PRESSURE PIPE, 12 MM (1/2 IN.) THROUGH 51 MM (2 IN.), FOR WATER SERVICE

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-12-2016

    Publisher:  American Water Works Association

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
     I Introduction
     II Special Issues
     III Use of This Standard
     IV Major Revisions
     V Comments
    Standard
     1 General
     2 References
     3 Definitions
     4 Requirements
     5 Verification
     6 Delivery
    Appendix
    A Bibliography for Additional
      Information

    Abstract - (Show below) - (Hide below)

    Specifies the requirements for composite polyethylene- aluminum-polyethylene pipe (hereinafter referred to as PE-AL-PE) in metric nominal inside diameter (ID) sizes 12 mm (1/2 in.) through 51 mm (2 in.).

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher American Water Works Association
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ANSI H35.1/H35.1M : 2017 ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM
    NSF 61 : 2016 DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
    PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
    ASTM F 1282 : 2017 : REDLINE Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
    PPI TR 4 : 2017 HDB/HDS/SDB/PDB/MRS LISTED MATERIALS - PPI LISTING OF HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESS (HDS), STRENGTH DESIGN BASIS (SDB), PRESSURE DESIGN BASIS (PDB) AND MINIMUM REQUIRED STRENGTH (MRS) RATINGS FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
    ASTM B 209 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
    ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
    ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
    ASTM E 8/E8M : 2016-09 TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more