Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ANSI INCITS 214 : 1992 : R2007

Current
Current

The latest, up-to-date edition.

INFORMATION SYSTEMS - 130-MM WRITE-ONCE OPTICAL DISK CARTRIDGE USING SAMPLED SERVO AND 4/15 ENCODING
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2007

Foreword
Introduction
Part 1: Unrecorded optical disk cartridge
1 Scope
2 Conformance
3 Normative references
4 Definitions
   4.1 case
   4.2 clamping zone
   4.3 control track
   4.4 cyclic redundancy check (CRC)
   4.5 defect management
   4.6 disk reference plane
   4.7 entrance surface
   4.8 error correction code (ECC)
   4.9 format
   4.10 groove
   4.11 hub
   4.12 interleaving
   4.13 land and groove
   4.14 mark
   4.15 optical disk
   4.16 optical disk cartridge (ODC)
   4.17 recording layer
   4.18 Reed-Solomon code
   4.19 spindle
   4.20 substrate
   4.21 track
   4.22 track pitch
5 General description
6 Environments
   6.1 Testing environment
   6.2 Operating environment
   6.3 Storage environments
7 Safety requirements
8 Dimensional and mechanical characteristics of the case
   8.1 General
   8.2 Case drawings
   8.3 Sides, reference axes and reference planes
   8.4 Materials
   8.5 Mass
   8.6 Overall dimensions (figure 3)
   8.7 Location hole (figure 3)
   8.8 Alignment hole (figure 3)
   8.9 Surfaces for reference planes P (figures 4 and 4a)
   8.10 Insertion slots and detent features (figure 5)
   8.11 Gripper slots (figure 6)
   8.12 Write-inhibit holes (figure 7)
   8.13 Media sensor holes (figure 8)
   8.14 Head and motor window (figure 10)
   8.15 Shutter (figure 11)
   8.16 Slot for shutter opener (figure 11)
   8.17 Shutter sensor notch (figure 9)
   8.18 User label areas (figure 13)
9 Dimensional and physical characteristics of the disk
   9.1 Dimensions of the disk
   9.2 Mass
   9.3 Moment of inertia
   9.4 Imbalance
   9.5 Axial deflection
   9.6 Axial acceleration
   9.7 Dynamic radial runout
   9.8 Radial acceleration
   9.9 Tilt
10 Drop test
11 Interface between disk and drive
   11.1 Clamping technique
   11.2 Dimensions of the hub (figure 1)
   11.3 Magnetizable material
   11.4 Clamping force
   11.5 Capture cylinder for the hub (figure 12)
   11.6 Disk position in the operating condition (figure 12)
12 Characteristics of the substrate
   12.1 Index of refraction
   12.2 Thickness
   12.3 Birefringence
13 Characteristics of the recording layer
   13.1 Test conditions
   13.2 Baseline reflectance
   13.3 Definitions of signals
   13.4 Prerecorded marks
   13.5 User-written data
Annexes
Annex A (informative) Office environment
Annex B (informative) Transportation
Annex C (normative) Measurement of birefringence
Annex D (normative) Definition of write and erase pulse width
Part 2: Recording format
1 Scope
2 Conformance
3 Conventions and notations
4 Features common to both formats
   4.1 Track geometry
   4.2 Formatted zone
   4.3 Control tracks
   4.4 Control track PEP zone
   4.5 Control track SFP zones
   4.6 Requirements for interchange
5 Format A
   5.1 Track layout
   5.2 Sector format
   5.3 Defect management
6 Format B
   6.1 Track layout
   6.2 Data structure
Annexes
Annex A (informative) Values to be implemented in future
        standards
Annex B (normative) CRC for ID fields of Format A
Annex C (normative) Interleave, CRC, ECC, Resync for the
        Data field of Format A
Annex D (informative) Linear Replacement Map Defect
        Management (LDM)

Describes definitions of essential concepts; the environment in which the characteristics are to be tested; the environments in which the cartridge is to be operated and stored; the mechanical, physical and dimensional characteristics of the case and of the optical disk; the optical characteristics and the recording characteristics for recording the information once and for reading it many times, so as to provide physical interchangeability between data processing systems.

Committee
X3B11
DocumentType
Standard
Pages
118
ProductNote
Reconfirmed 2007
PublisherName
Information Technology Industry Council
Status
Current

ISO 683-13:1974 Heat-treated steels, alloy steels and free-cutting steels Part 13: Wrought stainless steels
IEC 60950:1999 Safety of information technology equipment

View more information
$98.22
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more