AS 1302-1991

1 - AS 1302-1991 STEEL REINFORCING BARS FOR CONCRETE
4 - PREFACE
5 - CONTENTS
6 - 1 SCOPE
6 - 2 REFERENCED DOCUMENTS
6 - 3 DEFINITIONS
6 - 3.1 Angle of deformation flanks
6 - 3.2 Bar size
6 - 3.3 Calculated mass per metre
6 - 3.4 Deformed bar
6 - 3.5 Longitudinal rib
6 - 3.6 Nominal area
6 - 3.7 Plain round bar
6 - 3.8 Transverse deformation
6 - 3.9 Transverse deformation angle
6 - 3.10 Transverse deformation spacing
7 - 4 GRADE CLASSIFICATION AND DESIGNATION
7 - 4.1 Classification
7 - 4.2 Designation
7 - 5 CHEMICAL COMPOSITION
7 - 5.1 General
7 - 5.2 Cast analysis
7 - 5.3 Product analysis
7 - 5.4 Residual elements
7 - 6 MARGINS OF MANUFACTURE
8 - 7 QUALITY OF FINISHED BAR
8 - 8 DEFORMATION REQUIREMENTS FOR ANCHORAGE WITH CONCRETE
8 - 8.1 General
8 - 8.2 Spacing of transverse deformations
9 - 8.3 Transverse deformation angle
9 - 8.4 Gap between rows of transverse deformations
9 - 8.5 Height of transverse deformations
9 - 8.6 Height of longitudinal rib
9 - 8.7 Angle of deformation flanks
9 - 9 PREPARATION OF TEST PIECES FOR MECHANICAL TESTING
9 - 9.1 General
9 - 9.2 Tensile test pieces
9 - 9.3 Bend test pieces
9 - 10 MECHANICAL TEST REQUIREMENTS
9 - 10.1 Tensile test
10 - 10.2 Bend test
10 - 11 ROUNDING OF NUMBERS
10 - 11.1 General
10 - 11.2 Tensile properties
10 - 12 REVERSE-BEND TEST
10 - 13 MARKING
11 - APPENDIX A - PURCHASING GUIDELINES
11 - A1 INFORMATION TO BE SUPPLIED BY THE PURCHASER
11 - A2 CERTIFICATES OF COMPLIANCE AND TEST CERTIFICATES
11 - A2.1 Certificates of compliance
11 - A2.2 Test certificates
11 - A3 INSPECTION
12 - APPENDIX B - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
12 - B1 SCOPE
12 - B2 STATISTICAL SAMPLING
12 - B3 PRODUCT CERTIFICATION-STANDARDSMARK
12 - B4 SUPPLIER’S QUALITY SYSTEM
12 - B5 OTHER MEANS OF ASSESSMENT
12 - B5.1 General
12 - B5.2 Sampling and testing
13 - B5.3 Compliance
13 - B5.4 Retests
14 - APPENDIX C - REVERSE-BEND TEST FOR REINFORCING BARS
14 - C1 SCOPE
14 - C2 APPARATUS
14 - C3 PREPARATION OF THE TEST PIECE
14 - C4 PROCEDURE
14 - C5 ASSESSMENT OF RESULTS OF THE REVERSE-BEND TEST
15 - APPENDIX D - METHOD OF MEASUREMENT OF DEFORMATIONS
15 - D1 TRANSVERSE DEFORMATION SPACING
15 - D2 HEIGHT OF TRANSVERSE DEFORMATIONS
15 - D2.1 Average height method
15 - D2.2 Peak height method
15 - D3 HEIGHT OF LONGITUDINAL RIB
15 - D4 ANGLE OF DEFORMATION FLANKS

This Standard specifies requirements for plain and deformed hot-rolled bars for use as reinforcement for concrete. It applies to reinforcement supplied in straight lengths or in coil form. The following significant changes to the previous edition have been made: fabrication requirements have been amended to comply with AS 3600 and tolerances on straightness of reinforcing bars have been added.

This Standard specifies requirements for plain and deformed hot-rolled steel bars for use as reinforcement for concrete. It applies to reinforcement supplied in straight lengths or in coil form. For coiled material, the requirements apply to the straightened product.NOTES:For 'Purchasing Guidelines', see Appendix A.For 'Means for demonstrating compliance with this Standard', see Appendix B.For welding of bars complying with this Standard, see AS 3600 and AS 1554.3.This Standard is not applicable to prestressing steels.

Under Revision see DR 98119 (in part) For history before 1977 see Preface.
Second edition AS 1302-1977.
Third edition 1982.
Fourth edition 1991. For history before 1977 see Preface. Second edition AS 1302-1977. Third edition 1982. Fourth edition 1991.