We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • AS 1310-1987

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Steel wire for tendons in prestressed concrete

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  24-05-2018

    Language(s):  English

    Published date:  01-01-1987

    Publisher:  Standards Australia

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 - AS 1310-1987 STEEL WIRE FOR TENDONS IN PRESTRESSED CONCRETE
    4 - PREFACE
    4 - CONTENTS
    5 - 1 SCOPE.
    5 - 2 REFERENCED DOCUMENTS.
    5 - 3 DEFINITIONS.
    5 - 3.1 Calculated mass per metre
    5 - 3.2 Coil
    5 - 3.3 Nominal diameter of indented wire
    5 - 3.4 Lot
    5 - 3.5 Relaxation
    5 - 4 CHEMICALCOMPOSITION.
    5 - 5 WIRE MANUFACTURE.
    5 - 5.1 General.
    5 - 5.2 As-drawn wire.
    5 - 5.3 Stress-relieved wire.
    5 - 6 WELDS.
    5 - 7 QUALITY OF FINISHED WIRE.
    5 - 8 DIMENSIONS AND TOLERANCES.
    5 - 8.1 Tolerance on diameter of round wire.
    6 - 8.2 Tolerance on diameter of indented or crimped wire.
    6 - 8.3 Dimensions of indent.
    6 - 8.4 Depth and pitch of crimped wire.
    6 - 9 SPECIFIC REQUIREMENTS FOR STRESS-RELIEVED WIRE.
    6 - 9.1 Straightness.
    6 - 9.2 Coil sizes.
    6 - 10 ASSESSMENT OF COMPLIANCE.
    7 - 11 TESTING.
    8 - 12 RETESTS.
    8 - 13 ROUNDING OF NUMBERS.
    8 - 14 TEST CERTIFICATE.
    8 - 15 MARKING.
    8 - 16 PACKING.
    9 - APPENDIX A - PURCHASING GUIDELINES
    9 - A1 GENERAL.
    9 - A2 INFORMATION TO BE SUPPLIED BY PURCHASER.
    9 - A3 FACILITIES FOR TESTING.
    9 - A4 INSPECTION.
    10 - APPENDIX B - BEND TEST
    10 - B1 SCOPE.
    10 - B2 PRINCIPLE.
    10 - B3 APPARATUS.
    10 - B4 SAMPLING.
    10 - B5 PROCEDURE.
    10 - B6 REPORT.
    11 - APPENDIX C - RELAXATION TEST
    11 - C1 SCOPE.
    11 - C2 PRINCIPLE.
    11 - C3 TEST RIG.
    11 - C4 TEST CONDITIONS.
    11 - C5 PROCEDURE.
    11 - C6 CALCULATION.
    11 - C7 REPORT.

    Abstract - (Show below) - (Hide below)

    Specifies requirements for hard-drawn high-tensile steel wire intended for use in the prestressing of concrete. It provides for wire types in the as-drawn and stress-relieved conditions.

    Scope - (Show below) - (Hide below)

    This Standard specifies the requirements for hard-drawn, high-tensile steel wire intended for the prestressing of concrete.The Standard provides for the following wire types:(a) As-drawn condition - round wire only.(b) Stress-relieved condition - either round wire or round wire deformed by indenting or crimping,and stress-relieved to achieve either normal relaxation or low relaxation, as desired.NOTE: Guidelines to purchasers on requirements that should be specified by the purchaser and those that should be agreed at the time of enquiry or order are given in Appendix A.

    General Product Information - (Show below) - (Hide below)

    Committee BD-084
    Document Type Standard
    Publisher Standards Australia
    Status Superseded
    Superseded By
    Supersedes
    Under Revision

    Standards Referenced By This Book - (Show below) - (Hide below)

    AS 2505.4-2002 Metallic materials Wire - Reverse bend test
    AS 2706-2003 Numerical values - Rounding and interpretation of limiting values (Reconfirmed 2018)
    AS 1391-2007 Metallic materials - Tensile testing at ambient temperature
    AS 1545-1976 Methods for the calibration and grading of extensometers (Reconfirmed 2017)
    AS 2193-2005 Calibration and classification of force-measuring systems (Reconfirmed 2017)

    Standards Referencing This Book - (Show below) - (Hide below)

    AS/NZS 4671:2001 Steel reinforcing materials
    AS 4065-1992 Concrete poles for overhead lines and street lighting
    AS 5100.5-2004 Bridge design - Concrete
    AS 3600-2001 Concrete structures
    AS/NZS 1100.501:2002 Technical drawing Structural engineering drawing (Reconfirmed 2014)
    AS 5100.7:2017 Bridge design Bridge assessment
    AS 4672.1:2007 Steel prestressing materials General requirements
    AS 3600-1994 Concrete structures
    AS/NZS 1314:2003 Prestressing anchorages (Reconfirmed 2016)
    AS 1311-1987 Steel tendons for prestressed concrete-7-wire stress-relieved steel strand for tendons in prestressed concrete
    AS 3700-1998 Masonry structures
    AS/NZS 4065:2010 Concrete utility services poles
    AS 1085.14-2003 Railway track material Prestressed concrete sleepers
    AS 3700-2001 Masonry structures
    AS/NZS 4065:2000 Concrete utility services poles
    AS 1085.14-1997 Railway permanent way material - Part 14: Prestressed concrete sleepers
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective