AS 1397-2011
AvailableSuperseded
An Available Superseded Standard is one, which has been made available for a period of time although it has been formally superseded by another Standard. Its availability is maintained where it is referenced in legislation/regulations or in other Standards and its use should be restricted to where so referenced. No responsibility is taken by Intertek Inform as to the ongoing technical validity of such a Standard, the responsibility resting with the referencing authority.
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
15-09-2011
Specifies requirements for continuously hot-dip metallic coated sheet steel and strip supplied in thicknesses up to and including 5.0mm.
This Standard specifies requirements for continuously hot-dip metallic coated sheet steel and strip supplied in thicknesses up to and including 5.0 mm.Requirements for product conformity to this Standard are given in Appendix B.Requirements covered in this Standard are as follows:Formability grades of steel.Structural grades of steel.Classes of zinc coating, including differential coatings.Classes of zinc coating converted to zinc/iron alloy.Classes of zinc/aluminium coatings.Classes of zinc/aluminium/magnesium alloy coating.Classes of aluminium/zinc alloy coating.Classes of aluminium/zinc/magnesium alloy coating.Surface finish.Advice and recommendations on information to be supplied by the purchaser at the time of enquiry or order are contained in Appendix A.The specified requirements apply to the full length and full width of the product supplied, unless otherwise indicated.Within the description of the classes of coatings, the majority element present is listed first, followed by the next major element and followed by a third element if appropriate.
| Committee |
MT-001
|
| DocumentType |
Standard
|
| ISBN |
978 0 7337 9925 9
|
| Pages |
28
|
| PublisherName |
Standards Australia
|
| Status |
AvailableSuperseded
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
First published as part of AS A20-1934.Second edition 1947.Revised and redesignated in part as AS G24-1967.Revised and redesignated as AS 1397-1973.Second edition 1977.Third edition 1984.Fourth edition 1993.Fifth edition 2001. Originated as part of AS A20-1934. Previous edition AS1397-2001. Sixth edition 2011. Reissued incorporating Amendment No. 1 (October 2012).
| AS 1391-2007 | Metallic materials - Tensile testing at ambient temperature |
| AS/NZS 1050.39:1994 | Methods for the analysis of iron and steel Determination of chromium content - Flame atomic absorption spectrometric method (Reconfirmed 2016) |
| AS/NZS 1050.38:1994 | Methods for the analysis of iron and steel Determination of vanadium content - Flame atomic absorption spectrometric method (Reconfirmed 2016) |
| AS/NZS 1050.24:1994 | Methods for the analysis of iron and steel Determination of aluminium content - Spectrophotometric method (Reconfirmed 2016) |
| AS 1199.2-2003 | Sampling procedures for inspection by attributes Sampling plans indexed by limiting quality (LQ) for isolated lot inspection (Reconfirmed 2016) |
| AS/NZS 4680:2006 | Hot-dip galvanized (zinc) coatings on fabricated ferrous articles (Reconfirmed 2017) |
| AS 1199.4-2003 | Sampling procedures for inspection by attributes Procedures for assessment of declared quality levels (Reconfirmed 2016) |
| AS/NZS 1365:1996 | Tolerances for flat-rolled steel products (Reconfirmed 2016) |
| AS/NZS 1050.26:1994 | Methods for the analysis of iron and steel Silicon in iron and steel - Spectrophotometric method (Reconfirmed 2016) |
| AS 1199.3-2003 | Sampling procedures for inspection by attributes Skip-lot sampling procedures (Reconfirmed 2016) |
| AS 2706-2003 | Numerical values - Rounding and interpretation of limiting values (Reconfirmed 2018) |
| AS/NZS 1050.28:1994 | Methods for the analysis of iron and steel Vanadium in steel - Potentiometric method (Reconfirmed 2016) |
| AS/NZS 1050.18:1994 | Methods for the analysis of iron and steel Determination of phosphorus - Spectrophotometric method (Reconfirmed 2016) |
| AS/NZS 1050.8:1994 | Methods for the analysis of iron and steel Determination of manganese content - Spectrophotometric method (Reconfirmed 2016) |
| AS 1397-2001 | Steel sheet and strip - Hot-dipped zinc-coated or aluminium/zinc-coated |
| AS/NZS 1050.37:1994 | Methods for the analysis of iron and steel Determination of copper content - Flame atomic absorption spectrometric method (Reconfirmed 2016) |
| AS/NZS 1050.6:1995 | Methods for the analysis of iron and steel Determination of tin content - Flame atomic absorption spectrometric method (Reconfirmed 2016) |
| AS/NZS 1050.14:1994 | Methods for the analysis of iron and steel Determination of manganese in iron and steel - Titrimetric method |
| AS 2505.1-2004 | Metallic materials Sheet, strip and plate - Bend tests |
| AS/NZS 1050.21:1994 | Methods for the analysis of iron and steel Determination of cobalt content - Spectrophotometric method (Reconfirmed 2016) |
| AS 1199.0-2003 | Sampling procedures for inspection by attributes Introduction to the ISO 2859 attribute sampling system (Reconfirmed 2016) |
| AS 2490-1997 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| AS/NZS 1050.2:1994 | Methods for the analysis of iron and steel Determination of carbon content - Gravimetric method (Reconfirmed 2016) |
| AS/NZS 1050.27:1994 | Methods for the analysis of iron and steel Determination of titanium content - Spectrophotometric method (Reconfirmed 2016) |
| AS 2331.2.3-2001 | Methods of test for metallic and related coatings Tests for average coating mass per unit area or for thickness - Hydrogen evolution method for zinc coatings |
| AS/NZS 1050.1:1996 | Methods for the analysis of iron and steel Sampling iron and steel for chemical analysis |
| AS 2331.2.1-2001 | Methods of test for metallic and related coatings Tests for average coating mass per unit area or for thickness - Dissolution methods - Strip and weigh, and analytical |
| AS/NZS 1050.16:1994 | Methods for the analysis of iron and steel Determination of sulfur content - Infrared absorption method after combustion in an induction furnace (Reconfirmed 2017) |
| AS/NZS 1050.31:1994 | Methods for the analysis of iron and steel Determination of niobium content - PAR spectrophotometric method (Reconfirmed 2016) |
| AS/NZS 1050.32:1994 | Methods for the analysis of iron and steel Determination of carbon content - Infrared method (Reconfirmed 2017) |
| AS/NZS 1050.30:1994 | Methods for the analysis of iron and steel Determination of boron content - Curcumin spectrophotometric method |
| AS 1199.1-2003 | Sampling procedures for inspection by attributes Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection (Reconfirmed 2016) |
| AS/NZS 1050.20:1994 | Methods for the analysis of iron and steel Determination of magnesium content - Flame atomic absorption spectrometric method (Reconfirmed 2016) |
| AS 2699.2:2020 | Built-in components for masonry construction Connectors and accessories |
| AS 2304:2019 | Water storage tanks for fire protection systems |
| AS/NZS 3500.4:2015 | Plumbing and drainage Heated water services |
| AS/NZS 1577:2013 | Scaffold decking components |
| AS/NZS 4600:2018 | Cold-formed steel structures |
| AS 1445-2013 | Hot-dipped zinc-coated, aluminium/zinc-coated or aluminium/zinc/magnesium-coated steel sheet - 76 mm pitch corrugated |
| AS 4312:2019 | Atmospheric corrosivity zones in Australia |
| AS/NZS 3500.5:2012 | Plumbing and drainage Housing installations |
| AS/NZS 3500.5:2012 | Plumbing and drainage Housing installations |
| AS/NZS 2728:2013 | Prefinished/prepainted sheet metal products for interior/exterior building applications - Performance requirements |
| AS 1562.1:2018 | Design and installation of metal roof and wall cladding Metal |
| AS 3700:2018 | Masonry Structures |
| AS/NZS 5601.2:2020 | Gas installations LP Gas installations in caravans and boats for non-propulsive purposes |
| AS 4285:2019 | Rooflights |
| AS 2699.1:2020 | Built-in components for masonry construction Wall ties |
| AS/NZS 5601.1:2013 | Gas installations General installations |
| AS 4254.2-2012 | Ductwork for air-handling systems in buildings Rigid duct |
| AS 2699.3:2020 | Built-in components for masonry construction Lintels and shelf angles (durability requirements) |
| AS/NZS 1577:2018 | Scaffold decking components |
| AS/NZS 5601.2:2013 | Gas installations LP Gas installations in caravans and boats for non-propulsive purposes |
| AS/NZS 2589:2017 | Gypsum linings - Application and finishing |
| AS/NZS 2327:2017 | Composite structures - Composite steel-concrete construction in buildings |
| AS 1743:2018 | Road signs - Specifications |
| AS/NZS 5131:2016 | Structural steelwork - Fabrication and erection |
| AS 3864.1-2012 | Medical refrigeration equipment - For the storage of blood and blood products Manufacturing requirements |
| AS 2050:2018 | Installation of Roof Tiles |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.