Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search
  • Preview

    AS 1824.1-1995

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Insulation co-ordination Definitions, principles and rules

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Withdrawn date:  29-06-2017

    Language(s): 

    Published date:  31-12-1994

    Publisher:  Standards Australia

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    Specifies the procedure for the selection of the standard withstand voltages for the phase-to-earth, phase-to-phase and longitudinal insulation of the equipment and the installation of three-phase a.c. systems having a highest voltage for equipment above 1 kV. It also lists the standardized values from which the standard withstand voltages shall be selected. This Standard is technically equivalent to and has been reproduced from IEC 71-1:1993.

    Scope - (Show below) - (Hide below)

    This part of International Standard IEC 71 applies to three-phase a.c. systems having a highest voltage for equipment above 1 kV. It specifies the procedure for the selection of the standard withstand voltages for the phase-to-earth, phase-to-phase and longitudinal insulation of the equipment and the installations of these systems. It also gives the lists of the standardized values from which the standard withstand voltages shall be selected. This part recommends that the selected withstand voltages should be associated with the highest voltage for equipment. This association is for insulation co-ordination purposes only. The requirements for human safety are not covered by this Standard. Although the principles of this part also apply to transmission line insulation, the values of the withstand voltages may be different from the standard withstand voltages.The apparatus committees are responsible for specifying the withstand voltages and the test procedures suitable for the relevant equipment taking into consideration the recommendations of this Standard.NOTE û In IEC 71-2 Application Guide, (under revision), all rules for insulation co-ordination given in this Standard are justified in detail, in particular the association of the standard withstand voltages with the highest voltage for equipment. When more than one set of standard withstand voltages is associated with the same highest voltage for equipment, guidance is provided for the selection of the most suitable set.

    General Product Information - (Show below) - (Hide below)

    Committee EL-007
    Document Type Standard
    Publisher Standards Australia
    Status Withdrawn
    Supersedes

    History - (Show below) - (Hide below)

    Amendment 1 to As 1824.1-1995 see DR 96289 First published as AS C337-1963.Revised and redesignated AS 1824.1-1976.Second edition 1985.Third edition 1995. First published as AS C337-1963. Revised and redesignated AS 1824.1-1976. Second edition 1985. Third edition 1995.

    Standards Referenced By This Book - (Show below) - (Hide below)

    AS 2926-1987 Standard voltages - Alternating (50 Hz) and direct
    AS 1931.1-1996 High-voltage test techniques - General definitions and test requirements

    Standards Referencing This Book - (Show below) - (Hide below)

    AS/NZS 2081.5:2002 Electrical equipment for coal and shale mines - Electrical protection devices - Earth-fault current limiters
    AS 1137.3-1981 Insulators - Porcelain and glass indoor and outdoor station post insulators (for voltages greater than 1000 V a.c.)
    AS 60044.2-2007 Instrument transformers Inductive voltage transformers (IEC 60044-2:Ed.1.2 (2003) MOD)
    AS 2735-1984 Dry-type power transformers
    AS 3007.2-2004 Electrical installations - Surface mines and associated processing plant - General protection requirements
    AS 1265-1990 Bushings for alternating voltages above 1000 V
    AS/NZS 60137:2008 Insulated bushings for alternating voltages above 1000 V (IEC 60137, Ed. 5.0 (2003) MOD)
    AS/NZS 60076.3:2008 Power transformers Insulation levels, dielectric tests and external clearances in air (IEC 60076-3, Ed. 2 (2000) MOD)
    AS/NZS 4871.1:2010 Electrical equipment for mines and quarries General requirements
    AS 1824.2-1985 Insulation coordination (phase-to-earth and phase-to-phase, above 1 kV) - Application guide
    AS 1418.10(INT)-2004 Cranes, hoists and winches Elevating work platforms
    AS 2067-1984 Switchgear assemblies and ancillary equipment for alternating voltages above 1 kV
    AS 60044.1-2007 Instrument transformers Current transformers (IEC 60044-1 Ed.1.2 (2003) MOD)
    AS/NZS 2947.2:2002 Insulators - Porcelain and glass for overhead power lines - Voltages greater than 1000 V a.c.
    AS/NZS 60265.1:2001 High-voltage switches Switches for rated voltages above 1 kV and less than 52 kV (IEC 60265-1:1998, MOD) (Reconfirmed 2016)
    AS 4899-2007 Pin insulators - Porcelain and glass for overhead power lines - Voltages greater than 1000 V a.c. (Reconfirmed 2018)
    AS/NZS 1418.10:2011 Cranes, hoists and winches Mobile elevating work platforms
    AS 62103-2006 Electronic equipment for use in power installations
    AS 3439.1-1993 Low-voltage switchgear and controlgear assemblies - Type-tested and partially type-tested assemblies
    AS 60038-2012 Standard voltages
    AS/NZS 2650:2000 Common specifications for high-voltage switchgear and controlgear standards
    AS 2067-2008 Substations and high voltage installations exceeding 1 kV a.c.
    AS 60204.11-2006 Safety of machinery - Electrical equipment of machines Requirements for HV equipment for voltages above 1000 V a.c. or 1500 V d.c and not exceeding 36 kV (IEC 60204-11, Ed. 1.0 (2000) MOD)
    AS 60044.5-2004 Instrument transformers Capacitor voltage transformers
    AS 2374.3.1-1992 Power transformers Insulation levels and dielectric test - External clearances in air
    AS 4398.1-1996 Insulators - Ceramic or glass - Station post for indoor and outdoor use - Voltages greater than 1000 V a.c. Characteristics (Reconfirmed 2016)
    AS 1243-1982 Voltage transformers for measurement and protection
    AS/NZS 3947.1:1998 Low-voltage switchgear and controlgear General rules
    AS/NZS 2947.4:1999 Insulators - Porcelain and glass for overhead power lines - Voltages greater than 1000 V a.c. Test methods - Insulator strings and insulator sets
    AS 2374.3.0-1982 Power transformers Insulation levels and dielectric tests - General requirements
    AS IEC 60433-2007 Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic insulators for a.c. systems - Characteristics of insulator units of the long rod type
    AS 2067:2016 Substations and high voltage installations exceeding 1 kV a.c.
    AS 3851-1991 The calculation of short-circuit currents in three-phase a.c. systems (Reconfirmed 2015)
    AS 60265.2-2005 High-voltage switches High-voltage switches for rated voltages of 52 kV and above (IEC 60265-2, Ed.1.0(1988) MOD)
    AS 3947.1-1993 Low-voltage switchgear and controlgear General rules
    AS 4398.2-1996 Insulators - Ceramic or glass - Station post for indoor and outdoor use - Voltages greater than 1000 V a.c. Tests
    AS 1931.2-1996 High-voltage test techniques - Measuring systems
    AS 4398.2-2005 Insulators - Ceramic or glass - Station post for indoor or outdoor use - Voltages greater than 1000 V a.c. Tests (IEC 60168, Ed. 4.2 (2001) MOD)
    AS 2897-1986 Power capacitors - Shunt - Rated voltages above 660 v a.c.
    AS/NZS 3439.1:2002 Low-voltage switchgear and controlgear assemblies Type-tested and partially type tested assemblies (IEC 60439-1:1999 MOD)
    AS 2650-2005 Common specifications for high-voltage switchgear and controlgear standards (IEC 60694 Ed.2.2(2002) MOD)
    AS/NZS 4871.1:2012 Electrical equipment for mines and quarries General requirements
    AS/NZS 3947.1:2001 Low-voltage switchgear and controlgear General rules
    AS/NZS 3007:2013 Electrical equipment in mines and quarries - Surface installations and associated processing plant
    AS 60947.1-2004 Low-voltage switchgear and controlgear - General rules
    AS 1025.2-1989 High-voltage a.c. switchgear and controlgear - Switches and switch-disconnectors - For rated voltages of 52 kV and above
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more