AS/NZS 4130:2003

1 - AS/NZS 4130:2003 POLYETHYLENE (PE) PIPES FOR PRESSURE APPLICATIONS
4 - PREFACE
5 - CONTENTS
6 - FOREWORD
7 - 1 SCOPE AND APPLICATION
7 - 1.1 Scope
7 - 1.2 Application
7 - 2 REFERENCED DOCUMENTS
8 - 3 DEFINITIONS
8 - 3.1 Brittle failure
9 - 3.2 Co-extruded 'jacket' pipes
9 - 3.3 Ductile mode
9 - 3.4 Hoop stress
9 - 3.5 Hydrostatic design stress (HDS)
9 - 3.6 Liquefied petroleum gas (LPG)
9 - 3.7 Lower prediction limit of the predicted hydrostatic strength ...
9 - 3.8 Maximum allowable operating pressure (MAOP)
9 - 3.9 Minimum required strength (MRS)
9 - 3.10 Out-of-roundness (ovality)
9 - 3.11 Pipe material temperature
10 - 3.12 Standard dimension ratio (SDR)
10 - 3.13 Working pressure
10 - 4 NOTATION
10 - 5 OVERALL SERVICE (DESIGN) COEFFICIENT
10 - 6 CLASSIFICATION
16 - 7 COMPOSITION
16 - 7.1 General
16 - 7.2 Rework material
17 - 7.3 Striping and jacket compounds
17 - 7.3.1 General
17 - 7.3.2 Thermal stability of striping compounds
17 - 7.3.3 Dispersion
17 - 7.3.4 Weathering resistance
17 - 7.3.5 Cohesive resistance
17 - 8 COLOUR
17 - 8.1 General
18 - 8.2 Stripes and jackets
18 - 8.2.1 General
18 - 8.2.2 Yellow
18 - 8.2.3 Blue
18 - 8.2.4 Lilac
18 - 9 GENERAL REQUIREMENTS
18 - 9.1 Diameter and wall thickness
18 - 9.1.1 Tables 2, 3 and 4
19 - 9.1.2 Special applications
19 - 9.2 Length
19 - 9.3 Coiled pipe
19 - 9.4 Out of roundness
19 - 9.5 Freedom from defects
19 - 9.5.1 General
19 - 9.5.2 Pipe ends
19 - 9.5.3 Cleanliness
19 - 9.6 Effect on water
19 - 10 PERFORMANCE REQUIREMENTS
19 - 10.1 Resistance to internal pressure
20 - 10.2 Reversion
20 - 10.3 Thermal stability
20 - 10.4 Slow crack growth resistance
21 - 11 MARKING
22 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
22 - A1 SCOPE
22 - A2 RELEVANCE
22 - A3 DEFINITIONS
22 - A3.1 Acceptable quality level (AQL)
22 - A3.2 Batch
22 - A3.3 Batch release test (BRT)
22 - A3.4 Inspection level
22 - A3.5 Lot
22 - A3.6 New formulation
22 - A3.7 Process verification test (PVT)
23 - A3.8 Sample
23 - A3.9 Sampling plan
23 - A3.10 Type test (TT)
23 - A4 PRODUCT CERTIFICATION
23 - A5 MINIMUM SAMPLING AND TESTING FREQUENCY PLAN
23 - A5.1 General
23 - A5.2 Retesting
23 - A5.3 Rejection after test
25 - APPENDIX B - CALCULATION OF MAXIMUM ALLOWABLE OPERATING PRESSURE (MAOP) AT 20 C FOR SERIES 1, 2 AND 3 PIPES
25 - B1 SCOPE
25 - B2 SERIES 1 PIPES
25 - B3 SERIES 2 PIPES
25 - B4 SERIES 3 PIPES
26 - APPENDIX C - DESIGN FACTORS
28 - APPENDIX D - DIMENSIONAL REQUIREMENTS OF PIPES FOR SPECIAL APPLICATIONS

Specifies requirements for polyethylene pipes for the conveyance of fluids under pressure. Such fluids include, but are not restricted to, water, wastewater, slurries, compressed air, and fuel gas.

This Standard specifies requirements for polyethylene pipes for the conveyance of fluids under pressure. Such fluids include, but are not restricted to, water, wastewater, slurries, compressed air, and fuel gas. Fuel gas includes natural gas, liquefied petroleum gas (LPG) in the vapour phase and LPG/air mixtures. The partial pressure of the LPG is not to exceed 300 kPa. Methods for demonstrating compliance with this Standard are given in Appendix A.

First published in Australia in part as AS K119-1962.Second edition 1969.Revised and redesignated AS 1159-1973.AS 1667.1 first published 1974.AS 1667.2 first published 1974.Second edition AS 1159-1979.Second edition AS 1667.1-1984.Second edition AS 1667.2-1984.AS 2718.1 first published 1984.AS 2718.2 first published 1984.Third edition AS 1159-1988.AS 1159-1988 revised and redesignated in part as AS 4130(Int)-1993.First published in New Zealand in part as NZS 1189:1953 (endorsement of BS 1973:1953.).Revised and redesignated NZSS 2034-1965.Revised and redesignated NZSS 7602-1977.NZS 7646 first published 1978.NZS 7610 first published 1991.AS 4130(Int)-1993, AS 1667.1-1984, AS 1667.2-1984, AS 2718.1-1984, AS 2718.2-1984 and part of NZS 7602-1977, NZS 7646-1978, NZS 7610-1991 jointly revised, amalgamated and redesignated AS/NZS 4130:1997.Third edition 2001.Fourth edition 2003. First published in Australia in part as AS K119-1962. Second edition 1969. Revised and redesignated AS 1159-1973. AS 1667.1 first published 1974. AS 1667.2 first published 1974. Second edition AS 1159-1979. Second edition AS 1667.1-1984. Second edition AS 1667.2-1984. AS 2718.1 first published 1984. AS 2718.2 first published 1984. Third edition AS 1159-1988. AS 1159-1988 revised and redesignated in part as AS 4130(Int)-1993. First published in New Zealand in part as NZS 1189:1953 (endorsement of BS 1973:1953.). Revised and redesignated NZSS 2034-1965. Revised and redesignated NZSS 7602-1977. NZS 7646 first published 1978. NZS 7610 first published 1991. AS 4130(Int)-1993, AS 1667.1-1984, AS 1667.2-1984, AS 2718.1-1984, AS 2718.2-1984 and part of NZS 7602-1977, NZS 7646-1978, NZS 7610-1991 jointly revised, amalgamated and redesignated AS/NZS 4130:1997. Third edition 2001. Fourth edition 2003.