We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • AS/NZS 61347.2.9:2004

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Lamp controlgear Particular requirements for ballasts for discharge lamps (excluding fluorescent lamps) (IEC 61347-2-9:2000 MOD)

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  20-02-2019

    Language(s):  English

    Published date:  17-05-2004

    Publisher:  Standards Australia

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION1 Scope2 Normative references3 Definitions4 General requirements 4.1 Capacitors and other components 4.2 Thermally protected ballasts5 General notes on tests6 Classification7 Marking 7.1 Mandatory markings 7.2 Information to be provided, if applicable 7.3 Other information8 Protection against accidental contact with live parts9 Terminals, cords and cables10 Provisions for earthing11 Moisture resistance and insulation12 Electric strength13 Thermal endurance test for windings14 Ballast heating15 High-voltage impulse testing16 Fault conditions17 Construction18 Creepage distances and clearances19 Screws, current-carrying parts and connections20 Resistance to heat, fire and tracking21 Resistance to corrosionAnnexesAnnex A (normative) - Test to establish whether a conductive part is a live part which may cause an electric shockAnnex B (normative) - Particular requirements for thermally protected lamp controlgearAnnex C (normative) - Particular requirements for electronic lamp controlgear with means of protection against overheatingAnnex D (normative) - Requirements for carrying out the heating tests of thermally protected lamp controlgearAnnex E (normative) - Use of constant S other than 4500 in t[w] testsAnnex F (normative) - Draught-proof enclosureAnnex G (normative) - Explanation of the derivation of the values of pulse voltagesAnnex H (normative) - TestsAnnex I (normative) - Method for selection of varistorsAnnex J (informative) - Explanation of ballast temperatures

    Abstract - (Show below) - (Hide below)

    Specifies particular safety requirements for ballasts for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. This Standard is reproduced from IEC 61347-2-9:2000 including its Amendment 1:2003.

    Scope - (Show below) - (Hide below)

    This part of AS/NZS 61347 specifies particular safety requirements for ballasts for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. The standard covers inductive-type ballasts for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with discharge lamps, having rated wattages, dimensions and characteristics as specified in IEC 60188, IEC 60192 and IEC 60662. This standard applies to complete ballasts and to their component parts such as reactors, transformers and capacitors. Particular requirements for thermally protected ballasts are given in annex B. NOTE 1 For certain types of discharge lamps, an ignitor is required. NOTE 2 Ballasts for fluorescent lamps are covered by AS/NZS 61347.2.8. Performance requirements are the subject of AS/NZS 60923.

    General Product Information - (Show below) - (Hide below)

    Committee EL-041
    Document Type Standard
    Publisher Standards Australia
    Status Superseded
    Superseded By
    Supersedes
    Under Revision

    History - (Show below) - (Hide below)

    First published in Australia as part of AS 1468-1974.Jointly revised and redesignated AS/NZS 60922:1998.Jointly revised and redesignated AS/NZS 61347.2.9:2004. First published in Australia as part of AS 1468-1974. Jointly revised and redesignated AS/NZS 60922:1998. Jointly revised and redesignated AS/NZS 61347.2.9:2004.

    Standards Referenced By This Book - (Show below) - (Hide below)

    AS/NZS 61347.1:2002 Lamp controlgear General and safety requirements (IEC 61347-1:2000, MOD)
    AS/NZS 60923:1998 Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements (Reconfirmed 2013)
    AS/NZS 61347.2.1:2002 Lamp controlgear Particular requirements for starting devices (other than glow starters)

    Standards Referencing This Book - (Show below) - (Hide below)

    AS/NZS IEC 61347.2.13:2013 Lamp controlgear Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules (IEC 61347-2-13, Ed.1.0 (2006) MOD)
    AS/NZS 60927:2005 Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements (IEC 60927, Ed.2.2 (2004) MOD)
    AS/NZS 1158.6:2004 Lighting for roads and public spaces Luminaires
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective