We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • AS/NZS ISO 3834.1:1999

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Quality requirements for welding - Fusion welding of metallic materials Guidelines for selection and use

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  30-06-2017

    Language(s):  English

    Published date:  05-06-1999

    Publisher:  Standards Australia

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 - AS/NZS ISO 3834.1:1999 QUALITY REQUIREMENTS FOR WELDING-FUSION WELDING OF METALLIC MATERIALS - GUIDELINES FOR SELECTION AND USE
    4 - PREFACE
    5 - CONTENTS
    6 - INTRODUCTION
    7 - 1 Scope
    7 - 2 Normative references
    8 - 3 Definitions
    8 - 3.1 contract
    8 - 3.2 special process:
    8 - 3.3 manufacturing organization:
    8 - 3.4 qualified person:
    8 - 3.5 construction:
    8 - 4 Selection of welding quality requirements
    9 - Annex A - Flow diagram for selection of welding quality requirements
    10 - Annex B - Summary comparison of welding quality requirements with regard to ISO 3834-2, ISO 3834-3 and ISO 3834-4
    12 - Annex C - Bibliography

    Abstract - (Show below) - (Hide below)

    Describes welding quality requirements suitable for application by manufacturers using welding as a means of fabrication for any type of fusion-welded construction. The guidelines define various approaches to quality requirements for welding fabrication, both in workshops and on sites and provide guidance for describing the capability of a manufacturer to be able to produce welded construction of the specified quality. They can also be used by any interested party as a basis for assessing a manufacturer's welding quality arrangments. This Standard is identical with and has been reproduced from ISO 3838-1:1994.

    Scope - (Show below) - (Hide below)

    The guidelines given in this part of ISO 3834 have been prepared to describe welding quality requirements suitable for application by manufacturers using welding as a means of fabrication. They are structured such that they can be used for fabrication of any type of fusion welded construction. They relate only to those aspects of the quality of the final construction which may be influenced by welding and allied processes.These guidelines define various approaches to quality requirements for welding fabrication, both in workshops and on sites and provide guidance for describing the capability of a manufacturer to be able to produce welded constructions of the specified quality. They can also be used by any interested party as a basis for assessing a manufacturers welding quality arrangements.These guidelines are intended as a guide for the preparation of regulatory or contractual requirements and for a manufacturer's management to define welding requirements for quality systems related to the type of welded construction. The guidelines are not structured to be used in isolation as part of any regulatory, contractual or managerial requirement.They are intended to be used for the following purposes:a) providing interpretation of the requirements in the ISO 9000 series of standards, as a guideline for specification and establishment of the part of the quality system related to control of welding as a "special process";b) providing guidelines to establish specifications and welding quality requirements, where a quality system according to ISO 9001 and ISO 9002 is not involved;(c) assessment of the welding quality requirements mentioned in a) or b) above.The application of this would typically occur in the following circumstances:- in contractual situations: specification of welding requirements for quality systems;- by manufacturers: establishment and maintenance of welding quality requirements;- by committees preparing structural codes or other application standards: specification of welding quality requirements;- by interested parties, e.g. third parties, customers or the manufacturer's management: assessment of welding quality requirements.

    General Product Information - (Show below) - (Hide below)

    Committee WD-003
    Document Type Standard
    Publisher Standards Australia
    Status Superseded
    Superseded By
    Supersedes
    Under Revision

    History - (Show below) - (Hide below)

    First published as AS/NZS ISO 3834.1:1999.

    Standards Referenced By This Book - (Show below) - (Hide below)

    AS/NZS ISO 3834.3:1999 Quality requirements for welding - Fusion welding of metallic materials Standards quality requirements
    AS/NZS ISO 8402:1994 Quality management and quality assurance - Vocabulary
    AS/NZS ISO 3834.2:1999 Quality requirements for welding - Fusion welding of metallic materials Comprehensive quality requirements
    AS/NZS ISO 3834.4:1999 Quality requirements for welding - Fusion welding of metallic materials Elementary quality requirements
    AS/NZS ISO 9002:1994 Quality systems - Model for quality assurance in production, installation and servicing
    AS/NZS ISO 9001:1994 Quality systems - Model for quality assurance in design, development, production, installation and servicing

    Standards Referencing This Book - (Show below) - (Hide below)

    MP 87.2:2007 Australian/New Zealand Certification Scheme for explosion-protected electrical equipment (ANZEx Scheme) Recognized Service Facilities Program - Basic rules and procedures
    AS/NZS 1554.1:2004 Structural steel welding Welding of steel structures
    AS 2214-2004 Certification of welding supervisors - Structural steel welding
    AS/NZS 1554.4:2004 Structural steel welding - Welding of high strength quenched and tempered steels
    AS/NZS 1554.7:2006 Structural steel welding Welding of sheet steel structures
    AS/NZS ISO 3834.3:1999 Quality requirements for welding - Fusion welding of metallic materials Standards quality requirements
    AS 1228-2006 Pressure equipment - Boilers
    AS 2885.2-2007 Pipelines - Gas and liquid petroleum - Welding
    AS/NZS ISO 3834.4:1999 Quality requirements for welding - Fusion welding of metallic materials Elementary quality requirements
    AS/NZS ISO 3834.2:1999 Quality requirements for welding - Fusion welding of metallic materials Comprehensive quality requirements
    AS/NZS 3788:2006 Pressure equipment - In-service inspection
    AS/NZS 1554.5:2004 Structural steel welding Welding of steel structures subject to high levels of fatigue loading
    AS/NZS 1554.3:2008 Structural steel welding - Welding of reinforcing steel
    AS/NZS 1665:2004 Welding of aluminium structures (Reconfirmed 2016)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective