We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM A 674 : 2018

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Practice for Polyethylene Encasement for Ductile Iron Pipe for Water or Other Liquids

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-11-2018

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    This practice covers materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile iron pipe.

    Scope - (Show below) - (Hide below)

    1.1This practice covers materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile iron pipe. It may also be used for polyethylene encasement of fittings, valves, and other appurtenances to ductile iron pipe systems.

    1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.2.1Important SI values are provided in brackets. Also, certain important SI values appear without brackets or parentheses.

    1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee A 04
    Document Type Standard Practice
    Publisher American Society for Testing and Materials
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 1922 : 2008 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 1709 : 2022 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1709 : 2004 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 4976 : 2006 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 4976 : 2000 : REV B Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 4976 : 2004 : REV A Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 1922 : 2015 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 1922 : 2006 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 4976 : 2004 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 1709 : 2015 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 4976 : 2012 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 1922 : 2003 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 1709 : 2009 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1709 : 1998 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 4976 : 2002 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 1709 : 2001 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1709 : 2016 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1922 : 2015 : R2020 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 1709 : 2008 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1922 : 2003 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 4976 : 2002 : EDT 1 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 1922 : 2005 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 1709 : 2016 : REV A : EDT 1 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1709 : 2003 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1922 : 2000 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 1922 : 2006 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 1709 : 2015 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    ASTM D 1922 : 2009 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
    ASTM D 4976 : 2012 : REV A Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
    ASTM D 1709 : 2016 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective