Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

ASTM B 807/B807M : 2013 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys
Available format(s)

PDF

Superseded date

17-08-2020

Language(s)

English

Published date

01-06-2013

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 02.02, 2014 Defines the controls required for extrusion press solution heat treatment of the 6xxx and 7xxx series aluminum alloys when ASTM material specifications allow use of this process in lieu of furnace solution heat treatment.

1.1This practice establishes the controls required for extrusion press solution heat treatment of the 6xxx and 7xxx series aluminum alloys in Table 1 when ASTM material specifications allow use of this process in lieu of furnace solution heat treatment. For the alloys listed in Table 1, this practice is an alternate process to solution heat treatment in a furnace, such as specified in Practice B918/B918M for the attainment of T3, T4, T6, T7, T8 and T9-type tempers (see ANSI H35.1/H35.1M).

1.2This practice applies only to extrusion press solution heat treatment for aluminum alloys. Precipitation hardening (aging) processing and equipment calibration shall meet the practice and requirements of Practice B918/B918M.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The SI units are shown in brackets or in separate tables. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
B 07
DevelopmentNote
Supersedes ASTM B 807 (04/2006)
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM B 317/B317M : 2007 : R2015 : EDT 1 Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
ASTM B 317/B317M : 2007 : R2015 Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
ASTM B 317/B317M : 2007 Standard Specification for Aluminum-Alloy Extruded Bar, Rod, Tube, Pipe, Structural Profiles, and Profiles for Electrical Purposes (Bus Conductor)
SAE AMS 4172 : 2013 ALUMINUM ALLOY, EXTRUSIONS 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-T4511 OR T4510) SOLUTION HEAT TREATED AND STRESS RELIEVED BY STRETCHING
ASTM B 221 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
SAE AMS 4150 : 2013 ALUMINUM ALLOY, EXTRUSIONS AND RINGS 1.0MG - 0.60SI - 0.28CU - 0.20CR - (6061-T6) SOLUTION AND PRECIPITATION HEAT TREATED
SAE AMS 4173 : 2013 ALUMINUM ALLOY, EXTRUSIONS 1.0MG - 0.60SI - 0.30CU - 0.20CR (6061-T6511 OR T6510) SOLUTION HEAT TREATED, STRESS RELIEVED BY STRETCHING, STRAIGHTENED, AND PRECIPITATION HEAT TREATED
ASTM B 241/B241M : 2016 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
SAE AMS 4161 : 2013 ALUMINUM ALLOY, EXTRUSIONS 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-T4) SOLUTION HEAT TREATED AND NATURALLY AGED
ASTM B 881 : 2017 : REDLINE Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products

ANSI H35.1/H35.1M : 2017 ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM
ASTM B 557 : 2015 : REDLINE Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
ASTM E 10 : 2017-05 TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS
ASTM E 2281 : 2015 : REDLINE Standard Practice for Process Capability and Performance Measurement
ASTM B 557M : 2015 : REDLINE Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)

View more information
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more