ASTM B 818 : 2003 : R2018
Current
The latest, up-to-date edition.
Standard Specification for Cobalt-Chromium-Nickel-Molybdenum-Tungsten Alloy(UNS R31233) Plate, Sheet and Strip
Hardcopy , PDF
English
01-11-2018
CONTAINED IN VOL. 02.05, 2017 Describes equipment and test methods for determining the porosity of metallic coatings, where the pores penetrate down to a silver, copper, or copper-alloy substrate.
1.1 This specification covers cobalt-chromium-nickel-molybdenum-tungsten alloy UNS R31233 in the form of rolled plate, sheet, and strip for wear applications and general corrosion service.
1.2 The following products are covered under this specification:
1.2.1 Sheet and Strip—Hot or cold rolled, annealed and descaled unless solution-annealing is performed in an atmosphere yielding a bright finish.
1.2.2 Plate—Hot rolled, solution-annealed, and descaled.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
B 02
|
| DocumentType |
Standard
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
| ASTM B 545 : 2013 : REDLINE | Standard Specification for Electrodeposited Coatings of Tin |
| ASTM B 877 : 1996 : R2003 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method |
| ASTM B 867 : 1995 | Standard Specification for Electrodeposited Coatings of Palladium-Nickel for Engineering Use |
| ASTM B 679 : 1998 | Standard Specification for Electrodeposited Coatings of Palladium for Engineering Use |
| ASTM B 867 : 1995 : R2013 | Standard Specification for Electrodeposited Coatings of Palladium-Nickel for Engineering Use |
| ASTM B 689 : 1997 : R2003 | Standard Specification for Electroplated Engineering Nickel Coatings |
| ASTM B 689 : 1997 : R2013 | Standard Specification for Electroplated Engineering Nickel Coatings |
| ASTM B 877 : 1996 : R2013 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method |
| ASTM B 798 : 1995 : R2009 | Standard Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography |
| ASTM B 798 : 1995 : R2000 | Standard Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography |
| ASTM B 741 : 1995 : R2000 | Standard Test Method for Porosity In Gold Coatings On Metal Substrates By Paper Electrography (Withdrawn 2005) |
| ASTM B 679 : 1998 : R2004 : EDT 1 | Standard Specification for Electrodeposited Coatings of Palladium for Engineering Use |
| ASTM B 605 : 1995 : REV A : R2004 | Standard Specification for Electrodeposited Coatings of Tin-Nickel Alloy |
| ASTM B 735 : 2016 : REDLINE | Standard Test Method for Porosity in Gold Coatings on Metal Substrates by Nitric Acid Vapor |
| ASTM B 866 : 1995 : R2018 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion |
| ASTM B 765 : 2003 : R2013 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
| ASTM B 799 : 1995 : R2000 | Standard Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor |
| ASTM B 866 : 1995 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion |
| ASTM B 877 : 1996 : R2018 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method |
| ASTM B 877 : 1996 : R2008 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method |
| ASTM B 799 : 1995 : R2009 | Standard Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor |
| ASTM B 765 : 2003 : R2018 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
| I.S. EN ISO 10308:2006 | METALLIC COATINGS - REVIEW OF POROSITY TESTS |
| ASTM B 866 : 1995 : R2003 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion |
| ASTM B 799 : 1995 : R2005 | Standard Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor |
| ASTM B 765 : 2003 : R2008 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
| ASTM B 798 : 1995 : R2014 | Standard Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography |
| ASTM B 765 : 2003 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
| ASTM B 984 : 2012 | Standard Specification for Electrodeposited Coatings of Palladium- Cobalt Alloy for Engineering Use |
| ASTM B 866 : 1995 : R2008 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion |
| ASTM B 877 : 1996 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by the Phosphomolybdic Acid (PMA) Method |
| ASTM B 867 : 1995 : R2008 | Standard Specification for Electrodeposited Coatings of Palladium-Nickel for Engineering Use |
| ASTM B 866 : 1995 : R2013 | Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion |
| ASTM B 920 : 2016 : REDLINE | Standard Practice for Porosity in Gold and Palladium Alloy Coatings on Metal Substrates by Vapors of Sodium Hypochlorite Solution |
| ASTM B 605 : 1995 : REV A : R1999 | Standard Specification for Electrodeposited Coatings of Tin-Nickel Alloy |
| EN ISO 10308:2006 | Metallic coatings - Review of porosity tests (ISO 10308:2006) |
| ASTM B 867 : 1995 : R2003 | Standard Specification for Electrodeposited Coatings of Palladium-Nickel for Engineering Use |
| ASTM B 799 : 1995 : R2014 | Standard Test Method for Porosity in Gold and Palladium Coatings by Sulfurous Acid/Sulfur-Dioxide Vapor |
| ASTM B 689 : 1997 : R2008 | Standard Specification for Electroplated Engineering Nickel Coatings |
| ASTM B 679 : 1998 : R2015 | Standard Specification for Electrodeposited Coatings of Palladium for Engineering Use |
| ASTM B 689 : 1997 | Standard Specification for Electroplated Engineering Nickel Coatings |
| ASTM B 679 : 1998 : R2009 | Standard Specification for Electrodeposited Coatings of Palladium for Engineering Use |
| ASTM B 798 : 1995 : R2005 | Standard Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography |
| ASTM B 605 : 1995 : REV A : R2015 | Standard Specification for Electrodeposited Coatings of Tin-Nickel Alloy |
| ASTM B 605 : 1995 : REV A : R2009 | Standard Specification for Electrodeposited Coatings of Tin-Nickel Alloy |
| DIN EN ISO 10308:2006-04 | METALLIC COATINGS - REVIEW OF POROSITY TESTS |
| BS EN ISO 10308:2006 | Metallic coatings. Review of porosity tests |
| ISO 10308:2006 | Metallic coatings Review of porosity tests |
| ASTM B 906 : 2019 | Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip |
| ASTM B 741 : 1995 : R2000 | Standard Test Method for Porosity In Gold Coatings On Metal Substrates By Paper Electrography (Withdrawn 2005) |
| ASTM B 735 : 2016 : REDLINE | Standard Test Method for Porosity in Gold Coatings on Metal Substrates by Nitric Acid Vapor |
| ASTM B 542 : 2013 : REDLINE | Standard Terminology Relating to Electrical Contacts and Their Use |
| ASTM B 765 : 2003 : R2018 | Standard Guide for Selection of Porosity and Gross Defect Tests for Electrodeposits and Related Metallic Coatings |
| ASTM B 906 : 2022 | Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.