Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM B 947 : 2014 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Practice for Hot Rolling Mill Solution Heat Treatment for Aluminum Alloy Plate
Available format(s)

PDF

Language(s)

English

Published date

01-12-2014

CONTAINED IN VOL. 02.02, 2014 Gives the controls required for hot rolling mill solution heat treatment of the 6xxx series aluminum alloy plate.

1.1This practice establishes the controls required for hot rolling mill solution heat treatment of the 6xxx series aluminum alloy plate in Table 1 when ASTM material specifications allow use of this process instead of furnace solution heat treatment. For the alloys listed in Table 1, this practice is an alternate process to solution heat treatment in a furnace, such as specified in Practice B918 as the preliminary step for the attainment of T651-type tempers (see ANSI H35.1/H35.1M).

(A)These upper limit temperatures avoid the possibility of eutectic melting due to overheating, and include a safety margin of approximately 13°F [7°C].

1.2This practice applies only to hot rolling mill solution heat treatment of plate for the listed aluminum alloys. Precipitation hardening (aging), processing, and equipment calibration for aging shall meet the practice and requirements of Practice B918.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
B 07
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Current

ASTM B 209 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ASTM B 209M : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)
ASTM B 881 : 2017 : REDLINE Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products

ASTM B 918 : 2001 Standard Practice for Heat Treatment of Wrought Aluminum Alloys
ANSI H35.1M : 2004 ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM (METRIC)
EN 485-2:2016 ALUMINIUM AND ALUMINIUM ALLOYS - SHEET, STRIP AND PLATE - PART 2: MECHANICAL PROPERTIES
ASTM B 209M : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)
ASTM B 557 : 2015 : REDLINE Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
ASTM E 2281 : 2015 : REDLINE Standard Practice for Process Capability and Performance Measurement
ASTM B 557M : 2015 : REDLINE Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
ASTM B 209 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ANSI H35.1 : 2006 ALLOY AND TEMPER DESIGNATION SYSTEMS FOR ALUMINUM

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more