Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 1115 : 2017 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
Available format(s)

PDF

Language(s)

English

Published date

15-09-2017

CONTAINED IN VOL. 04.07, 2017 Defines products composed of dense elastomeric silicone rubber that are fabricated into gaskets and accessories (such as setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction.

1.1This specification describes products composed of dense elastomeric silicone rubber that are fabricated into gaskets and accessories (such as setting blocks, spacers, and shims) for use in sealing and glazing applications in building construction. These products are used to seal or serve as components of compression sealing systems between mechanically restrained surfaces in building construction and also as components in structural silicone sealant glazing systems.

1.2The following precautionary statement pertains only to the test method portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.3Test Method C1166, as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment that takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.

1.4The values stated in metric (SI) units are to be regarded as the standard. The inch-pound values given in parentheses are provided for information purposes only.

1.5The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 24
DocumentType
Redline
Pages
6
PublisherName
American Society for Testing and Materials
Status
Current

AWWA D108 : 2010 ALUMINUM DOME ROOFS FOR WATER STORAGE FACILITIES
ASTM C 1242 : 2018-03 GUIDE FOR SELECTION, DESIGN, AND INSTALLATION OF DIMENSION STONE ATTACHMENT SYSTEMS
ASTM C 1401 : 2014 : REDLINE Standard Guide for Structural Sealant Glazing
CSA A440 : 2017 NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS
A500-16 Building guards

ASTM D 1149 : 2016-02 TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 3182 : 2016 : REDLINE Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
ASTM C 1087 : 2016 : REDLINE Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM D 1566 : 2015 : REDLINE TERMINOLOGY RELATING TO RUBBER
ASTM D 925 : 2014 : REDLINE Standard Test Methods for Rubber Property—Staining of Surfaces (Contact, Migration, and Diffusion)

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more