Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 1157 : 2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Performance Specification for Hydraulic Cement
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

10-08-2002

1.1 This specification covers hydraulic cements for both general and special applications. This is a specification giving performance requirements. There are no restrictions on the composition of the cement or its constituents.

1.2 The specification classifies cements by type based on specific requirements for general use, high early strength, resistance to attack by sulfates, and heat of hydration. Optional requirements are provided for the property of low reactivity with alkali-reactive aggregates.

1.3 For properties where values are given in both SI and inch-pound units, the values in SI units are to be regarded as the standard. Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in Standard IEEE/ASTM SI 10, of measurements made in other units.

1.4 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1—Specification C 150 is a prescription specification for portland cement and specification C 595 is a specification for blended hydraulic cement where the products that may be furnished are of restricted nature and proportions and where the products must meet prescriptive requirements as to chemical and physical properties.

Committee
C 01
DocumentType
Standard
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 1492 : 2003 : R2016 Standard Specification for Concrete Roof Tile
ASTM C 185 : 2015 : REV A Standard Test Method for Air Content of Hydraulic Cement Mortar
ASTM C 1372 : 2017 Standard Specification for Dry-Cast Segmental Retaining Wall Units
ASTM C 595/C595M : 2019 Standard Specification for Blended Hydraulic Cements
ASTM C 55 : 2017 Standard Specification for Concrete Building Brick
ASTM C 1319 : 2017 Standard Specification for Concrete Grid Paving Units
ASTM C 1778 : 2016 Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete
ASTM E 2277 : 2014 Standard Guide for Design and Construction of Coal Ash Structural Fills
ASTM C 917/C917M : 2018 Standard Test Method for Evaluation of Variability of Cement from a Single Source Based on Strength
ASTM C 1436 : 2013 Standard Specification for Materials for Shotcrete (Withdrawn 2022)
ASTM C 1713 : 2017 Standard Specification for Mortars for the Repair of Historic Masonry
ASTM C 139 : 2017 Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes
ASTM C 387/C387M : 2017 Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
ASTM C 109/C109M : 2016 : REV A Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
ASTM C 1480/C1480M : 2007 : R2012 Standard Specification for Packaged, Pre-Blended, Dry, Combined Materials for Use in Wet or Dry Shotcrete Application (Withdrawn 2021)
ASTM C 688 : 2014 Standard Specification for Functional Additions for Use in Hydraulic Cements
ASTM C 129 : 2017 Standard Specification for Nonloadbearing Concrete Masonry Units
ASTM C 226 : 2012 Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement
ASTM C 1660 : 2010 : R2018 Standard Specification for Thin-bed Mortar for Autoclaved Aerated Concrete (AAC) Masonry
ASTM C 1623 : 2017 : REV A Standard Specification for Manufactured Concrete Masonry Lintels
ASTM C 1634 : 2017 Standard Specification for Concrete Facing Brick

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more