Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 1157/C1157M : 2020

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Performance Specification for Hydraulic Cement
Available format(s)

Hardcopy , PDF

Superseded date

09-09-2023

Language(s)

English

Published date

22-04-2020

1.1This performance specification covers hydraulic cements for both general and special applications. There are no restrictions on the composition of the cement or its constituents (see Note 1).

Note 1:There are two related hydraulic cement standards, Specification C150/C150M for portland cement and Specifications C595/C595M for blended cements, both of which contain prescriptive and performance requirements

1.2This performance specification classifies cements based on specific requirements for general use, high early strength, resistance to attack by sulfates, and heat of hydration. Optional requirements are provided for the property of low reactivity with alkali-silica-reactive aggregates and for air-entraining cements.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice.

1.4The text of this performance specification refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 01
DocumentType
Standard
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 595/C595M : 2020 Standard Specification for Blended Hydraulic Cements
ASTM C 1731 : 2016 Standard Specification for Concrete Floor Tile
ASTM C 1688/C1688M : 2014 : REV A Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete (Withdrawn 2023)
ASTM C 94/C94M : 2020 Standard Specification for Ready-Mixed Concrete
ASTM C 1707 : 2018 Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes
ASTM C 913 : 2018 Standard Specification for Precast Concrete Water and Wastewater Structures
ASTM C 465 : 2019 Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements
ASTM C 1491 : 2019 Standard Specification for Concrete Roof Pavers (Withdrawn 2023)
ASTM C 1778 : 2020 Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete
ASTM C 1804 : 2020 Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles
ASTM C 1634 : 2020 Standard Specification for Concrete Facing Brick and Other Concrete Masonry Facing Units
ASTM C 476 : 2020 Standard Specification for Grout for Masonry
ASTM C 109/C109M : 2020 : REV B Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens)
ASTM C 185 : 2020 Standard Test Method for Air Content of Hydraulic Cement Mortar
ASTM C 936/C936M : 2020 Standard Specification for Solid Concrete Interlocking Paving Units
ASTM C 1884 : 2019 Standard Specification for Concrete Ballast Block
ASTM C 1012/C1012M : 2018 : REV B Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
ASTM C 1782/C1782M : 2020 : REV A Standard Specification for Segmental Concrete Paving Slabs
ASTM C 1904 : 2020 Standard Test Methods for Determination of the Effects of Biogenic Acidification on Concrete Antimicrobial Additives and/or Concrete Products
ASTM C 685/C685M : 2017 Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing
ASTM C 183/C183M : 2016 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
ASTM C 226 : 2019 Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement
ASTM C 887 : 2020 Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar
ASTM C 1240 : 2020 Standard Specification for Silica Fume Used in Cementitious Mixtures
ASTM C 563 : 2020 Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement
ASTM C 90 : 2016 : REV A Standard Specification for Loadbearing Concrete Masonry Units
ASTM C 1903 : 2021 Standard Specification for Precast Concrete Duct Bank
ASTM C 1837 : 2017 Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures
ASTM C 151/C151M : 2018 Standard Test Method for Autoclave Expansion of Hydraulic Cement
ASTM C 1846/C1846M : 2019 Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
ASTM C 1581/C1581M : 2018 : REV A Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage
ASTM C 1776/C1776M : 2017 Standard Specification for Wet-Cast Precast Modular Retaining Wall Units
ACI PRC-549.3:2022 Glass Fiber-Reinforced Concrete Premix—Report

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more