Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 1249 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
Available format(s)

Hardcopy , PDF

Superseded date

17-02-2023

Language(s)

English

Published date

16-07-2018

1.1This guide covers design and fabrication considerations for the edge seal of conventionally sealed insulating glass units, herein referred to as IG units. The IG units described are used in structural silicone sealant glazing systems, herein referred to as SSG systems. SSG systems typically are either two or four sided, glazed with a structural sealant. Other conditions such as one, three, five, six sided may be used.

1.2This guides does not cover the IG units of other than conventional edge seal design (Fig. 1); however, the information contained herein may be of benefit to the designers of such IG units.

FIG. 1 Sealed IG Edge Seal: Basic Components

 Sealed IG Edge Seal: Basic Components Sealed IG Edge Seal: Basic Components

1.3In an SSG system, IG units are retained to a metal framing system by a structural seal (Fig. 2). The size and shape of that seal, as well as numerous other SSG system design considerations, are not addressed in this guide.

FIG. 2 Typical A-Side SSG System Mullion: Horizontal Section (Vertical Joint)

 Typical A-Side SSG System Mullion: Horizontal Section (Vertical Joint) Typical A-Side SSG System Mullion: Horizontal Section (Vertical Joint)

1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6The committee with jurisdiction for this standard is not aware of any comparable standard guides published by other organizations.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 24
DocumentType
Guide
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 1401 : 2014 : R2022 Standard Guide for Structural Sealant Glazing
ASTM E 2190 : 2019 Standard Specification for Insulating Glass Unit Performance and Evaluation
ASTM C 1401 : 2014 Standard Guide for Structural Sealant Glazing
ASTM C 1193 : 2016 Standard Guide for Use of Joint Sealants
ASTM C 1369 : 2019 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units

ASTM C 1184 : 2000 : REV A Standard Specification for Structural Silicone Sealants
ASTM C 794 : 2018 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
ASTM E 2189 : 2019 Standard Test Method for Testing Resistance to Fogging in Insulating Glass Units
ASTM E 2188 : 2010 Standard Test Method for Insulating Glass Unit Performance
ASTM C 1184 : 2018 : EDT 1 Standard Specification for Structural Silicone Sealants
ASTM E 2190 : 2010 Standard Specification for Insulating Glass Unit Performance and Evaluation
ASTM C 1369 : 2007 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM C 1135 : 2000 : R2011 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C 1184 : 2018 Standard Specification for Structural Silicone Sealants
ASTM C 1087 : 2000 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM E 2190 : 2008 Standard Specification for Insulating Glass Unit Performance and Evaluation
ASTM C 1369 : 2019 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM C 1135 : 2019 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C 1369 : 2007 : R2014 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM E 2189 : 2010 Standard Test Method for Testing Resistance to Fogging in Insulating Glass Units
ASTM C 1184 : 2000 : REV A : EDT 1 Standard Specification for Structural Silicone Sealants
ASTM C 1135 : 2000 : R2005 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM E 2190 : 2002 Standard Specification for Insulating Glass Unit Performance and Evaluation
ASTM C 1135 : 2000 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C 794 : 2018 : R2022 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
ASTM C 1135 : 2015 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C 1087 : 2016 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1087 : 2000 : R2011 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 679 : 2015 : R2022 Standard Test Method for Tack-Free Time of Elastomeric Sealants
ASTM E 2188 : 2002 Standard Test Method for Insulating Glass Unit Performance
ASTM E 2189 : 2010 : EDT 1 Standard Test Method for Testing Resistance to Fogging in Insulating Glass Units
ASTM C 1369 : 1997 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM C 1369 : 2002 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM C 679 : 2015 Standard Test Method for Tack-Free Time of Elastomeric Sealants
ASTM C 1184 : 2005 Standard Specification for Structural Silicone Sealants
ASTM E 2190 : 2019 Standard Specification for Insulating Glass Unit Performance and Evaluation
ASTM E 2189 : 2002 Standard Test Method for Testing Resistance to Fogging in Insulating Glass Units
ASTM C 1087 : 2000 : R2006 : EDT 1 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1087 : 2000 : R2006 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1184 : 2013 Standard Specification for Structural Silicone Sealants
ASTM C 1184 : 2014 Standard Specification for Structural Silicone Sealants
ASTM E 2188 : 2019 Standard Test Method for Insulating Glass Unit Performance

View more information
$135.86
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more