Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 1802 : 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
Available format(s)

Hardcopy , PDF

Superseded date

19-01-2015

Language(s)

English

Published date

15-12-2014

CONTAINED IN VOL. 04.05, 2018 Defines the design, testing, manufacture, selection, and installation of fabricated metal access hatches for utility, water, and wastewater structures including utility vaults, drainage structures, valve vaults, meter vaults, wet wells, pump enclosures, utility trenches, piping trenches, and drainage trenches.

1.1This specification covers the design, testing, manufacture, selection, and installation of fabricated metal access hatches for utility, water, and wastewater structures including utility vaults, drainage structures, valve vaults, meter vaults, wet wells, pump enclosures, utility trenches, piping trenches, and drainage trenches.

1.2This specification is applicable to various configurations of access hatches constructed of fabricated metal of various materials and grades for various loading conditions, traffic speeds, or both.

1.3Engineering design and testing criteria are provided for access hatches to be located in various areas subjected to various loading conditions, traffic speed, frequency, or combinations thereof.

1.4Production loading criteria is provided to allow the access hatches to be tested to verify the load capacity of the manufactured hatches.

1.5Hatch loading selection guidelines are included to allow selection of the proper hatch design loading for the conditions of the actual area of placement.

1.6The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered the standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
C 27
DocumentType
Standard
Pages
25
PublisherName
American Society for Testing and Materials
Status
Superseded

ASTM C 858 : 2019 Standard Specification for Underground Precast Concrete Utility Structures

ASTM C 857 : 2016 : REDLINE PRATICE FOR MINIMUM STRUCTURAL DESIGN LOADING FOR UNDERGROUND PRECAST CONCRETE UTILITY STRUCTURES
ASTM A 786/A786M : 2015 : REDLINE Standard Specification for Hot-Rolled Carbon, Low-Alloy, High-Strength Low-Alloy, and Alloy Steel Floor Plates
ASTM A 123/A123M : 2017 : REDLINE Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
ASTM A 666 : 2015 : REDLINE Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
AWS D1.2/D1.2M : 2014 STRUCTURAL WELDING CODE - ALUMINUM
ASTM B 221 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
ASTM A 913/A913M : 2015 : REDLINE Standard Specification for High-Strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-Tempering Process (QST)
ASTM A 656/A656M : 2013-11 SPECIFICATION FOR HOT-ROLLED STRUCTURAL STEEL, HIGH-STRENGTH LOW-ALLOY PLATE WITH IMPROVED FORMABILITY
ASTM E 2309/E2309M : 2016 : REDLINE Standard Practices for Verification of Displacement Measuring Systems and Devices Used in Material Testing Machines
ASTM B 316/B316M : 2015 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
AISC 360 : 2016 SPECIFICATION FOR STRUCTURAL STEEL BUILDINGS
ASCE 8 02 : 2002 SPECIFICATION FOR THE DESIGN OF COLD-FORMED STAINLESS STEEL STRUCTURAL MEMBERS
AWS D1.6/D1.6M : 2007 STRUCTURAL WELDING CODE - STAINLESS STEEL
ASTM B 209 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ASTM A 847/A847M : 2014 : REDLINE Standard Specification for Cold-Formed Welded and Seamless High-Strength, Low-Alloy Structural Tubing with Improved Atmospheric Corrosion Resistance
ASTM B 241/B241M : 2016 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
AWS D1.1/D1.1M : 2015 STRUCTURAL WELDING CODE-STEEL
ASTM B 928/B928M : 2015 : REDLINE Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments
ASTM B 247 : 2015 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings
ASTM A 588/A588M : 2015 : REDLINE Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance
ASTM C 890 : 2013 : REDLINE PRACTICE FOR MINIMUM STRUCTURAL DESIGN LOADING FOR MONOLITHIC OR SECTIONAL PRECAST CONCRETE WATER AND WASTEWATER STRUCTURES

View more information
$176.78
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more