Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM C 393 : 2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Flexural Properties of Sandwich Constructions
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

10-01-2000

CONTAINED IN VOL. 15.03, 2005 Determines the properties of flat sandwich constructions exposed to flat wise flexure in such a way that the applied moments create curvature of the sandwich facing planes.

1.1 This test method covers determination of the properties of flat sandwich constructions subjected to flatwise flexure in such a manner that the applied moments produce curvature of the sandwich facing planes.

1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given may be approximate.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 30
DocumentType
Test Method
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

MIL-HDBK-349 Base Document:1994 MANUFACTURE AND INSPECTION OF ADHESIVE BONDED, ALUMINUM HONEYCOMB SANDWICH ASSEMBLIES FOR AIRCRAFT
17/30342710 DC : 0 BS EN ISO 12215-5 - SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION
ASTM D 6416/D6416M : 2016 : REDLINE Standard Test Method for Two-Dimensional Flexural Properties of Simply Supported Sandwich Composite Plates Subjected to a Distributed Load
ASTM C 481 : 1999 Standard Test Method for Laboratory Aging of Sandwich Constructions
93/706616 DC : 0 PREN 2833-1 - AEROSPACE SERIES - TECHNICAL SPECIFICATION - GLASS FIBER THERMOSETTING PREIMPREGNATES - PART 1: GENERAL
ASTM C 481 : 1999 : R2005 Standard Test Method for Laboratory Aging of Sandwich Constructions
ASTM C 480 : 1999 : R2005 Standard Test Method for Flexure Creep of Sandwich Constructions
ISO 12215-5:2008 Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination
SAE AS 8056 : 2004(R2016) MINIMUM DESIGN AND PERFORMANCE OF AIRPLANE GALLEY IN-FLIGHT CARTS, CONTAINERS, AND ASSOCIATED COMPONENTS
ASTM C 481 : 1999 : R2011 Standard Test Method for Laboratory Aging of Sandwich Constructions
ASTM C 480 : 1999 Standard Test Method for Flexure Creep of Sandwich Constructions
DIN EN ISO 12215-5:2014-10 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014)
SAE AMS 3970/6 : 2011 CARBON FIBER FABRIC REPAIR PREPREG, 120 DEGREES C (250 DEGREES F) VACUUM CURING - PART 6 - MATERIAL SPECIFICATION: CARBON FIBER FABRIC REINFORCED EPOXY PREPREG FOR REPAIR, PLAIN WEAVE FABRIC, 193 G/M[2], ADHESIVE FILM FOR REPAIR AND NON-STRUCTURAL GLASS FIBER FABRIC REINFORCED EPOXY PREPREG, 105 G/M[2]
UNI EN ISO 12215-5 : 2014 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION
PREN 2833-1 : 200P2 AEROSPACE SERIES - GLASS FIBRE THERMOSETTING PREIMPREGNATES - TECHNICAL SPECIFICATION - PART 1: GENERAL REQUIREMENTS
SAE AMS 3710 : 2014 SANDWICH STRUCTURES, GLASS FABRIC-RESIN, LOW PRESSURE MOLDED, HEAT RESISTANT
SAE AMS STD 401 : 1999 SANDWICH CONSTRUCTIONS AND CORE MATERIALS - GENERAL TEST METHODS
BS EN ISO 12215-5 : 2008 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION
UNE-EN ISO 12215-5:2008 Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2008)
SAE AMS 3970/1 : 2011 CARBON FIBER FABRIC REPAIR PREPREG, 120 DEGREES C (250 DEGREES F) VACUUM CURING - PART 1 - GENERAL REQUIREMENTS
NF EN ISO 12215-5 : 2008 AMD 1 2014 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION
MIL-STD-401 Revision B:1967 SANDWICH CONSTRUCTIONS AND CORE MATERIALS, GENERAL TEST METHODS
ASTM C 481 : 1999 : R2016 Standard Test Method for Laboratory Aging of Sandwich Constructions
I.S. EN ISO 12215-5:2008 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008)
EN ISO 12215-5:2008/A1:2014 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008/AMD 1:2014)
SAE AMS A 25463 : 2013 ADHESIVE, FILM FORM, METALLIC STRUCTURAL SANDWICH CONSTRUCTION
SAE AMS 3715 : 2013 CORE, HONEYCOMB, GLASS/PHENOLIC
MIL-A-25463 Revision B:1982 ADHESIVE, FILM FORM, METALLIC STRUCTURAL SANDWICH CONSTRUCTION
15/30274132 DC : 0 BS ISO 18402 - TESTING STRUCTURES - STRUCTURAL INSULATED PANEL ROOF CONSTRUCTION - TEST METHODS

View more information
$108.03
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more