ASTM D 1430 : 2017 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
28-04-2022
English
17-03-2017
CONTAINED IN VOL. 08.01, 2017 Defines polychlorotrifluoroethylene (PCTFE) plastics that consist of at least 90% chlorotrifluoroethylene and are suitable for extrusion and for compression and injection molding.
1.1This classification system covers polychlorotrifluoroethylene (PCTFE) plastics that consist of at least 90 % chlorotrifluoroethylene and are suitable for extrusion and for compression and injection molding. Additional components allow for chemical modifications, such as co-monomers, but not colorants, fillers, plasticizers, or mechanical blends with other resins. This classification system does not cover recycled PCTFE materials.
1.2The physical and electrical properties of parts molded or extruded from PCTFE molding compounds vary with the crystalline content obtained during processing and subsequent annealing. Accordingly, the numerical values listed in Table 1 apply only to the test specimens molded in accordance with Section 8. These values are not applicable as design criteria to semi-finished and finished parts prepared and annealed under other conditions.
1.3The values stated in SI units as detailed in IEEE/SI-10 are to be regarded as the standard. The values given in parentheses are for information only.
1.4The following precautionary statement pertains only to the test methods portion, Section 10, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:Although this classification system and ISO 12086-1 (1995) and ISO 12086-2 (1995) differ in approach or detail, data obtained using either are technically equivalent.
| Committee |
D 20
|
| DevelopmentNote |
Supersedes L P 385 (07/2004)
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| I.S. EN ISO 12086-1:2006 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| BS EN ISO 12086-1:2006 | Plastics. Fluoropolymer dispersions and moulding and extrusion materials Designation system and basis for specifications |
| DIN EN ISO 12086-1:2006-05 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| DIN EN ISO 20568-1:2017-10 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017) |
| DIN EN ISO 20568-2:2017-10 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017) |
| MIL-DTL-3786 Revision J:2013 | SWITCHES, ROTARY (CIRCUIT SELECTOR, LOW-CURRENT CAPACITY), GENERAL SPECIFICATION FOR |
| UNE-EN ISO 20568-1:2017 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20568-1:2017) |
| I.S. EN ISO 12086-2:2006 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 20568-2 E : 2017 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017) |
| MIL-P-46036 Revision B:1973 | PLASTIC SHEET, RODS, TUBES AND DISCS, POLYCHLOROTRIFLUOROETHYLENE |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| I.S. EN ISO 20568-2:2017 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017) |
| MIL-DTL-2 Revision G:2006 | VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR |
| DIN EN ISO 20568-1:2015-07 (Draft) | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017) |
| BS EN ISO 12086-2:2006 | Plastics. Fluoropolymer dispersions and moulding and extrusion materials Preparation of test specimens and determination of properties |
| EN ISO 12086-1:2006/AC:2007 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| UNI EN ISO 12086-2 : 2006 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| SAE AMS 3650 : 2012 | RODS, SHEETS, AND MOLDED SHAPES, POLYCHLOROTRIFLURORETHYNEN (PCTFE) UNPLASTICIZED |
| 04/30091867 DC : DRAFT FEB 2004 | BS EN ISO 12086-1 - PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| BS EN ISO 20568-1:2017 | Plastics. Fluoropolymer dispersions and moulding and extrusion materials Designation system and basis for specifications |
| 15/30321222 DC : 0 | BS EN ISO 20568-1 - PLASTICS - FLUOROPOLYMER DISPERSION AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| 15/30321226 DC : 0 | BS EN ISO 20568-2 - PLASTICS - FLUOROPOLYMER DISPERSION AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| MIL-DTL-83522 Revision E:2013 | Connectors, Fiber Optic, Single Ferrule, General Specification for |
| BS ISO 12086-2 : 2001 AMD 10637 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS |
| ASTM D 7194 : 2012 : REDLINE | Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE) |
| ISO 20568-2:2017 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 12086-2:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ISO 20568-1:2017 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 1: Designation system and basis for specifications |
| ISO 12086-1:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 1: Designation system and basis for specifications |
| EN ISO 12086-2:2006/AC:2009 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 20568-2:2017 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20568-2:2017) |
| EN ISO 20568-1:2017 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 20568-1:2017) |
| I.S. EN ISO 20568-1:2017&LC:2017 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017) |
| UNE-EN ISO 20568-2:2017 | Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20568-2:2017) |
| DIN EN ISO 20568-1 E : 2017 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017) |
| BS ISO 12086-1 : 1995 AMD 10638 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| BS EN ISO 20568-2:2017 | Plastics. Fluoropolymer dispersions and moulding and extrusion materials Preparation of test specimens and determination of properties |
| 04/30091870 DC : DRAFT FEB 2004 | BS EN ISO 12086-2 - PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| MIL C 83522 : D | CONNECTORS, FIBER OPTIC, SINGLE TERMINUS, GENERAL SPECIFICATION FOR |
| DIN EN ISO 20568-2:2015-07 (Draft) | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017) |
| ASTM D 7211 : 2013-05 | SPECIFICATION FOR PARTS MACHINED FROM POLYCHLOROTRIFLUOROETHYLENE (PCTFE) AND INTENDED FOR GENERAL USE |
| DIN EN ISO 12086-2:2006-05 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| MIL-DTL-21604-1 Revision C:2009 | SWITCH, ROTARY, MULTIPOLE AND SELECTOR, 1 AMPERE, STYLES JF AND JFM |
| ASTM D 3418 : 2015 : REDLINE | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ISO 12086-1:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 1: Designation system and basis for specifications |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ISO 12086-2:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 7211 : 2013-05 | SPECIFICATION FOR PARTS MACHINED FROM POLYCHLOROTRIFLUOROETHYLENE (PCTFE) AND INTENDED FOR GENERAL USE |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| ASTM D 7194 : 2012 : REDLINE | Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE) |
| ASTM D 3892 : 2015 : REDLINE | PRACTICE FOR PACKAGING/PACKING OF PLASTICS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.