Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 1552 : 2007

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Sulfur in Petroleum Products (High-Temperature Method)
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

01-12-2007

p id="s00002">1.1 This test method covers three procedures for the determination of total sulfur in petroleum products including lubricating oils containing additives, and in additive concentrates. This test method is applicable to samples boiling above 177°C (350°F) and containing not less than 0.06 mass % sulfur. Two of the three procedures use iodate detection; one employing an induction furnace for pyrolysis, the other a resistance furnace. The third procedure uses IR detection following pyrolysis in a resistance furnace.

1.2 Petroleum coke containing up to 8 mass % sulfur can be analyzed.

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 02
DocumentType
Test Method
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 3238 : 2017 : REV A Standard Test Method for Calculation of Carbon Distribution and Structural Group Analysis of Petroleum Oils by the n-d-M Method
ASTM D 6823 : 2008 : R2013 Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils
ASTM D 1266 : 2018 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
ASTM E 1208 : 2016 Standard Practice for Fluorescent Liquid Penetrant Testing Using the Lipophilic Post-Emulsification Process
ASTM E 1220 : 2016 Standard Practice for Visible Penetrant Testing Using Solvent-Removable Process
ASTM D 6969 : 2017 Standard Practice for Preparation of Calcined Petroleum Coke Samples for Analysis
ASTM D 7467 : 2019 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
ASTM E 1210 : 2016 Standard Practice for Fluorescent Liquid Penetrant Testing Using the Hydrophilic Post-Emulsification Process
ASTM D 7578 : 2018 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 6376 : 2010 : R2017 : EDT 1 Standard Test Method for Determination of Trace Metals in Petroleum Coke by Wavelength Dispersive X-ray Fluorescence Spectroscopy
ASTM E 1418 : 2016 Standard Practice for Visible Penetrant Testing Using the Water-Washable Process
ASTM D 6448 : 2016 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 6443 : 2014 : R2019 : EDT 1 Standard Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure)
ASTM D 4951 : 2014 Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry
ASTM D 396 : 2019 Standard Specification for Fuel Oils
ASTM E 165/E165M : 2018 Standard Practice for Liquid Penetrant Testing for General Industry
ASTM D 240 : 2017 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
ASTM D 8056 : 2018 Standard Guide for Elemental Analysis of Crude Oil
ASTM D 3338/D3338M : 2009 : R2014 : EDT 2 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 7666 : 2012 Standard Specification for Triglyceride Burner Fuel
ASTM E 1209 : 2018 Standard Practice for Fluorescent Liquid Penetrant Testing Using the Water-Washable Process
ASTM E 1219 : 2016 Standard Practice for Fluorescent Liquid Penetrant Testing Using the Solvent-Removable Process
ASTM D 7455 : 2019 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 4868 : 2017 Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more