Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 2275 : 2014 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Voltage Endurance of Solid Electrical Insulating Materials Subjected to Partial Discharges (Corona) on the Surface
Available format(s)

PDF

Superseded date

28-04-2022

Language(s)

English

Published date

11-12-2014

CONTAINED IN VOL. 10.01, 2015 Describes solid electrical insulating materials for use at commercial power frequencies with respect to their voltage endurance under the action of corona.

1.1This test method determines the voltage endurance of solid electrical insulating materials for use at commercial power frequencies under the action of corona (see Note 1). This test method is more meaningful for rating materials with respect to their resistance to prolonged ac stress under corona conditions for comparative evaluation between materials.

Note 1:The term “corona” is used almost exclusively in this test method instead of “partial discharge,” because it is a visible glow at the edge of the electrode interface that is the result of partial discharge. Corona, as defined in Terminology D1711, is “visible partial discharges in gases adjacent to a conductor.”

1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

Committee
D 09
DocumentType
Redline
Pages
9
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 5047 : 2017 : REDLINE Standard Specification for Polyethylene Terephthalate Film and Sheeting
IEEE 1133-1988 IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications
ASTM D 3756 : 1997 : R2010 Standard Test Method for Evaluation of Resistance to Electrical Breakdown by Treeing in Solid Dielectric Materials Using Diverging Fields
IEEE DRAFT 434 : D10 2006 FUNCTIONAL EVALUATION OF INSULATION SYSTEMS FOR AC ELECTRIC MACHINES RATED 2300 V AND ABOVE
ASTM D 8065/D8065M : 2016 Standard Classification System and Basis for Specification for Specifying Plastic Films
ANSI/NEMA FI 3:2004 Calendered Aramid Papers Used for Electrical Insulation
IEEE 4-2013 IEEE Standard for High-Voltage Testing Techniques
ASTM D 3019 : 1994 : R2007 Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non Fibered, Asbestos Fibered, and Non Asbestos Fibered
IEEE 434-2006 IEEE Guide for Functional Evaluation of Insulation Systems for AC Electric Machines Rated 2300 V and Above
ASTM D 1868 : 2013 : REDLINE Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems
ASTM D 6097 : 2016 : REDLINE Standard Test Method for Relative Resistance to Vented Water-Tree Growth in Solid Dielectric Insulating Materials
ASTM D 3018/D3018M : 2011 Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules
ASTM D 3756 : 1997 Standard Test Method for Evaluation of Resistance To Electrical Breakdown By Treeing In Solid Dielectric Materials Using Diverging Fields
ASTM ES 19 : 1991 Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration (Withdrawn 1994)
ASTM D 3756 : 1997 : R2004 Standard Test Method for Evaluation of Resistance to Electrical Breakdown by Treeing in Solid Dielectric Materials Using Diverging Fields

ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
IEC 60343:1991 Recommended test methods for determining the relative resistance of insulating materials to breakdown by surface discharges
ASTM D 1711 : 2015 : REDLINE Standard Terminology Relating to Electrical Insulation
ASTM D 3382 : 2013 : REDLINE Standard Test Methods for Measurement of Energy and Integrated Charge Transfer Due to Partial Discharges (Corona) Using Bridge Techniques
ASTM D 1868 : 2013 : REDLINE Standard Test Method for Detection and Measurement of Partial Discharge (Corona) Pulses in Evaluation of Insulation Systems

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more