Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

18-02-2021

Publisher

American Society for Testing and Materials

1.1These test methods cover procedures for sampling, examination, physical testing, and analyses of asphalt-containing materials used in roofing and waterproofing. These materials include but are not limited to roll roofing, cap sheets, and shingles. Any of these materials is allowed to be partially or fully coated, surfaced, or laminated, or a combination thereof.

1.2The test methods and procedures in this standard appear in the following order:

Section	Content

6	Types of Roofing
7	Sampling
8	Mass and Area Determination
9	Selection of Representative Specimens
10	Moisture
11	Pliability
12	Mass Loss and Behavior on Heating
13	Tear Strength
14	Fastener Pull-Through Resistance
15	Preparation and Selection of Small Test Specimens for Analyses
16	Analysis of Glass Felt Products
17	Analysis of Roofing Products with Organic Felts
18	Ash of Desaturated Felt
19	Calculation
20	Adjusting Back Coating Fine Mineral Matter and Back Surfacing
21	Report
22	Precision and Bias

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 08
DocumentType	Test Method
Pages	13
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM D 228/D228M : 2019 : REV A

ASTM D 4897/D4897M : 2016	Standard Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing
ASTM D 7158/D7158M : 2020	Standard Test Method for Wind Resistance of Asphalt Shingles (Uplift Force/Uplift Resistance Method)
ASTM D 4601/D4601M : 2004 : R2020	Standard Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing
ASTM D 3462/D3462M : 2019	Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
ASTM D 6381/D6381M : 2015 : R2020	Standard Test Method for Measurement of Asphalt Shingle Mechanical Uplift Resistance
ASTM D 3105 : 2017	Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 1970/D1970M : 2020	Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection
ASTM D 2626/D2626M : 2004 : R2020	Standard Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing
ASTM D 6380/D6380M : 2003 : R2018	Standard Specification for Asphalt Roll Roofing (Organic Felt)
ASTM D 3018/D3018M : 2011 : R2017	Standard Specification for Class A Asphalt Shingles Surfaced with Mineral Granules
ASTM D 6757/D6757M : 2018	Standard Specification for Underlayment Felt Containing Inorganic Fibers Used in Steep-Slope Roofing
ASTM D 8257/D8257M : 2020	Standard Specification for Mechanically Attached Polymeric Roof Underlayment Used in Steep Slope Roofing

ASTM D 3909/D3909M : 2014 : R2021	Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
ASTM D 3909/D3909M : 2022	Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
ASTM D 1922 : 2023	Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 3462/D3462M : 2023	Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
ASTM D 2178/D2178M : 2015 : REV A : R2021	Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
ASTM D 4897/D4897M : 2016 : R2023	Standard Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing
ASTM D 6380/D6380M : 2003 : R2022	Standard Specification for Asphalt Roll Roofing (Organic Felt)
ASTM F 1667 : 2021	Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 95 : 2013 : R2018	Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
ASTM F 1667 : 2020	Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
ASTM D 3909/D3909M : 2014	Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced With Mineral Granules
ASTM D 1922 : 2015 : R2020	Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 2178/D2178M : 2015 : REV A	Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
ASTM D 6380/D6380M : 2003 : R2018	Standard Specification for Asphalt Roll Roofing (Organic Felt)
ASTM D 95 : 2023	Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation