ASTM D 2565 : 2016 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
Available format(s)
PDF
Superseded date
20-10-2023
Language(s)
English
Published date
12-10-2016
CONTAINED IN VOL. 08.02, 2016 Defines specific procedures and test conditions that are applicable for xenon-arc exposure of plastics conducted in accordance with Practices G 151 and G 155.
1.1This practice covers specific procedures and test conditions that are applicable for xenon-arc exposure of plastics conducted in accordance with Practices G151 and G155. This practice also covers the preparation of test specimens, the test conditions best suited for plastics, and the evaluation of test results.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:This practice and ISO 4892-2 address the same subject matter, but differ in technical content.
| Committee |
D 20
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM D 3218 : 2007 | Standard Specification for Polyolefin Monofilaments |
| ASTM F 1988 : 1999 : R2014 | Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use |
| ASTM D 5071 : 2006 | Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus |
| MIL-T-53048 Revision C:1991 | TANK, FABRIC, COLLAPSIBLE; AIR COLUMN SUPPORTED, OPEN TOP, WATER STORAGE 3000 GALLONS |
| CGSB 12.12 : M90 | PLASTIC SAFETY GLAZING SHEETS |
| MIL C 17 : G | CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERAL SPECIFICATION FOR |
| ASTM D 1047 : 2016 : REDLINE | Standard Specification for Poly(Vinyl Chloride) Jacket for Wire and Cable |
| CSA C411.4 : 2016 | COMPOSITE SUSPENSION INSULATORS FOR OVERHEAD LINES > 75 KV |
| CSA C411.6 : 2011 | LINE POST COMPOSITE INSULATORS FOR OVERHEAD DISTRIBUTION LINES <= 75 KV |
| ASTM F 2947/F2947M : 2014-03 | SPECIFICATION FOR 150 TO 1500 MM [6 TO 60 IN.] ANNULAR CORRUGATED PROFILE-WALL POLYETHYLENE (PE) PIPE AND FITTINGS FOR SANITARY SEWER APPLICATIONS |
| ASTM E 765 : 1980 | Practice for Evaluation of Cover Materials for Flat Plate Solar Collectors (Withdrawn 1991) |
| CSA B837:14 (R2019) | Collapsible fabric storage tanks (bladders) |
| ASTM F 1858 : 1998 : R2014 | Standard Performance Requirements for Multipositional Plastic Chairs with Adjustable Backs or Reclining Mechanisms for Outdoor Use |
| API 15S : 2016 | SPOOLABLE REINFORCED PLASTIC LINE PIPE |
| ASTM D 3435 : 1980 | Specification for Plastic Containers (Jerry Cans) for Petroleum Products (Withdrawn 1987) |
| ASTM D 3334 : 1980 | Methods of Testing Fabrics Woven from Polyolefin Monofilaments (Withdrawn 1990) |
| ASTM D 6662 : 2017 : REDLINE | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
| ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ASTM D 3105 : 2017 : REDLINE | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM D 5870 : 2016 : REDLINE | Standard Practice for Calculating Property Retention Index of Plastics |
| NFPA 1965 : 2014 | FIRE HOSE APPLIANCES |
| NFPA 1964 : 2018 | SPRAY NOZZLES |
| MIL-T-53101 Base Document:1990 | TANKS, FABRIC, COLLAPSIBLE, 3000, 10,000 & 20,000 GALLON, PETROLEUM, LOW TEMPERATURE |
| MIL-STD-1678-3 Revision C:2016 | FIBER OPTIC CABLING SYSTEMS REQUIREMENTS AND MEASUREMENTS - PART 3: PHYSICAL, MECHANICAL, ENVIRONMENTAL AND MATERIAL MEASUREMENTS (PART 3 OF 6 PARTS) |
| ASTM D 3218 : 2007 : R2018 | Standard Specification for Polyolefin Monofilaments |
| MIL-T-52983 Revision G:1994 | TANK, FABRIC, COLLAPSIBLE, 3,000 10,000 20,000 AND 50,000 GALLON, FUEL |
| ASTM F 1988 : 1999 : R2004 : EDT 1 | Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use |
| ASTM D 3218 : 2007 : R2012 | Standard Specification for Polyolefin Monofilaments |
| IEEE 1637-2010 | IEEE Guide to Select Terminations for Shielded Alternating-Current Power Cable Rated 5 kV - 46 kV |
| CSA C411.7 : 2011 : INC : UPD 2 : 2013 | COMPOSITE INSULATORS FOR GUY WIRES |
| ASTM D 5071 : 2006 : R2013 | Standard Practice for Exposure of Photodegradable Plastics in a Xenon Arc Apparatus |
| CSA B45.8 : 2013 | TERRAZZO, CONCRETE, AND NATURAL STONE PLUMBING FIXTURES |
| AWWA C901 : 2017 | POLYETHYLENE (PE) PRESSURE PIPE AND TUBING, 3/4 IN. (19 MM) THROUGH 3 IN. (76 MM), FOR WATER SERVICE |
| CSA C310 : 2009 : R2014 | DISTRIBUTION CLASS POLYMERIC CUTOUTS |
| ASTM D 1248 : 2016 : REDLINE | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 7031 : 2011 : REDLINE | GUIDE FOR EVALUATING MECHANICAL AND PHYSICAL PROPERTIES OF WOOD-PLASTIC COMPOSITE PRODUCTS |
| ASTM F 1858 : 1998 : R2008 | Standard Performance Requirements for Multipositional Plastic Chairs with Adjustable Backs or Reclining Mechanisms for Outdoor Use |
| ASTM F 1858 : 1998 : R2004 : EDT 1 | Standard Performance Requirements for Multipositional Plastic Chairs with Adjustable Backs or Reclining Mechanisms for Outdoor Use |
| ASTM F 1838 : 1998 | Standard Performance Requirements for Child's Plastic Chairs for Outdoor Use |
| ASTM F 1838 : 1998 : R2008 | Standard Performance Requirements for Child's Plastic Chairs for Outdoor Use (Withdrawn 2017) |
| ASTM F 1858 : 1998 | Standard Performance Requirements for Multipositional Plastic Chairs with Adjustable Backs or Reclining Mechanisms for Outdoor Use |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7436 : 2017 : REDLINE | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM G 178 : 2016 : REDLINE | Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique |
| ANSI C29.13 : 2012 | INSULATORS - COMPOSITE - DISTRIBUTION DEADEND TYPE |
| ANSI/NEMA C29.17:2013 | American National Standard for Composite Insulators—Transmission Line Post Type |
| ANSI/NEMA C29.18:2013 | American National Standard for Composite Insulators—Distribution Line Post Type |
| ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| MIL C 24643 : A | CABLES AND CORDS ELECTRIC, LOW SMOKE FOR SHIPBOARD USE, GENERAL SPECIFICATION FOR |
| MIL-DTL-32265 Base Document:2007 | Folded Fiberglass Mat Fabrication and Packaging |
| ASTM D 2672 : 2014 : REDLINE | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
| MIL C 85045 : E | CABLES, FIBER OPTICS, (METRIC), GENERAL SPECIFICATION FOR |
| CSA C411.6 : 2011 : R2016 | LINE POST COMPOSITE INSULATORS FOR OVERHEAD DISTRIBUTION LINES <= 75 KV |
| CSA C310 : 2009 | DISTRIBUTION CLASS POLYMERIC CUTOUTS |
| ASTM F 1988 : 1999 : R2004 | Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use |
| ASTM E 154/E154M : 2008 : REV A : R2013 : EDT 1 | Standard Test Methods for Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover |
| ICC IRC Code and Commentary Volume 1 : 2015 | IRC® Code and Commentary, Volume 1 |
| ASTM F 1561 : 2003 | Standard Performance Requirements for Plastic Chairs for Outdoor Use |
| CSA C310 : 2009 : INC : UPD 2 : 2012 | DISTRIBUTION CLASS POLYMERIC CUTOUTS |
| CGSB-43.44 : 1996 | BAGS FOR TRANSPORT OF FOOD AID |
| ASTM F 1561 : 2003 : R2008 | Standard Performance Requirements for Plastic Chairs for Outdoor Use |
| MIL C 24640 : A | CABLE, LIGHT WEIGHT, ELECTRIC, LOW SMOKE, FOR SHIPBOARD USE GENERAL SPECIFICATION FOR |
| MIL-T-53066 Revision B:1994 | TANK, FABRIC, COLLAPSIBLE, 5000 BARREL, FUEL |
| ASTM F 1988 : 1999 : R2008 | Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use |
| CSA C411.6 : 2011 : INC : UPD 2 : 2013 | LINE POST COMPOSITE INSULATORS FOR OVERHEAD DISTRIBUTION LINES <= 75 KV |
| CSA C411.7 : 2011 : R2016 | COMPOSITE INSULATORS FOR GUY WIRES |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| ASTM D 7032 : 2017 : REDLINE | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
| GOST 849:2018 | Primary nickel. SpecificationsE |
| MIL-PRF-15624 Revision H:2016 | GASKET MATERIAL, RUBBER, 50 DUROMETER HARDNESS (MAXIMUM) |
| ASTM F 790 : 2008 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| CSA C411.5 : 2016 | DEAD-END/SUSPENSION COMPOSITE INSULATORS FOR OVERHEAD LINES <= 75 KV |
| MIL DTL 17 : J | CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERAL SPECIFICATION FOR |
| CSA A440 : 2017 | NORTH AMERICAN FENESTRATION STANDARD/SPECIFICATION FOR WINDOWS, DOORS, AND SKYLIGHTS |
| CSA C411.7 : 2011 : INC : UPD 1 : 2011 | COMPOSITE INSULATORS FOR GUY WIRES |
| CSA C411.7 : 2011 | COMPOSITE INSULATORS FOR GUY WIRES |
| ASTM F 790 : 2008 : R2013 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM F 1561 : 2003 : R2014 | Standard Performance Requirements for Plastic Chairs for Outdoor Use |
| ASTM F 1988 : 1999 | Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use |
| ASTM F 1838 : 1998 : R2004 : EDT 1 | Standard Performance Requirements for Child's Plastic Chairs for Outdoor Use |
| SAE J 2527 : 2004 | PERFORMANCE BASED STANDARD FOR ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A CONTROLLED IRRADIANCE XENON-ARC APPARATUS |
| ASTM D 5870 : 2016 : REDLINE | Standard Practice for Calculating Property Retention Index of Plastics |
| SAE J 2412 : 2015 | Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Xenon-Arc Apparatus<br> |
| ASTM D 3980 : 1988 | Practice for Interlaboratoy Testing of Paint and Related Materials (Withdrawn 1998) |
| ASTM G 155 : 2013 : REDLINE | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ASTM G 113 : 2016 : REDLINE | Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials |
| ASTM G 147 : 2017 : REDLINE | Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests |
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.