ASTM D 2737 : 2012 : REV A
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Polyethylene (PE) Plastic Tubing
Available format(s)
Hardcopy , PDF
Superseded date
19-11-2020
Language(s)
English
Published date
12-12-2012
1.1This specification covers polyethylene (PE) plastic tubing in outside diameters and SDR’s that are pressure rated for water. Included are requirements for PE compounds, and requirements and test methods for PE plastic tubing workmanship, dimensions, elevated temperature sustained pressure, burst pressure and marking.
1.2The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes shall not be considered as requirements of the specification. Notes and footnotes in tables and figures, and Supplementary Requirements are requirements of the specification.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1—Joining PE plastic tubing with fittings that require flaring the tubing is not recommended because Practice D3140, the technique used to make the flare has been withdrawn (discontinued).
Note 2—References and PE compound descriptions for PE2305, PE2406, PE3306, PE3406, and PE3408 have been removed due to changes in Specification D3350 and PPI TR-3. For removed designations, refer to previous editions of Specification D2737, Specification D3350, PPI TR-3 and PPI TR-4. The removal of these PE compounds does not affect pipelines that are in service. PE compounds and material designations resulting from changes in Specification D3350 and PPI TR-3 are addressed in Section 5.
1.4The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 1055 : 2016 : REV A | Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing |
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 645 : 2018 : REV B | Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems |
| ASTM D 2837 : 2013 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1238 : 2000 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1238 : 2004 : REV C | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1598 : 2002 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1598 : 2015 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 4218 : 2020 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2837 : 2001 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1603 : 2001 | Standard Test Method for Carbon Black In Olefin Plastics |
| ASTM D 1238 : 2010 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3140 : 1990 | Standard Practice for Flaring Polyolefin Pipe and Tubing (Withdrawn 1999) |
| ASTM D 3350 : 2008 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4218 : 1996 : R2001 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
| ASTM D 2837 : 2002 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2001 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2004 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 3350 : 2002 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4218 : 1996 : R2008 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2837 : 2008 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2837 : 1998 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1598 : 1997 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2837 : 2001 : REV A : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 3350 : 2004 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1603 : 2020 | Standard Test Method for Carbon Black Content in Olefin Plastics |
| ASTM D 2837 : 2011 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 3350 : 2002 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 3350 : 2012 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2001 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1603 : 2011 | Standard Test Method for Carbon Black Content in Olefin Plastics |
| ASTM D 2565 : 1992 | Standard Practice for Operating Xenon Arc-Type Light-Exposure Apparatus with and Without Water for Exposure of Plastics |
| ASTM D 3350 : 2012 : EDT 1 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1603 : 1994 | Standard Test Method for Carbon Black In Olefin Plastics |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2565 : 1999 | Standard Practice for Xenon Arc Exposure of Plastics Intended for Outdoor Applications |
| ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1603 : 2006 | Standard Test Method for Carbon Black Content in Olefin Plastics |
| ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 4218 : 2015 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2565 : 1970 | Standard Recommended Practice For Operating Xenon Arc-Type (Water-Cooled) Light - And Water-Exposure Apparatus For Exposure Of Plastics |
| ASTM D 3350 : 2010 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1598 : 2002 : R2008 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 3350 : 2006 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 3350 : 2010 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2565 : 2016 | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications |
| ASTM D 1238 : 2001 : EDT 1 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1603 : 2014 | Standard Test Method for Carbon Black Content in Olefin Plastics |
| ASTM D 1603 : 2012 | Standard Test Method for Carbon Black Content in Olefin Plastics |
| ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2002 : R2009 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 1238 : 2004 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 3350 : 2005 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 4218 : 1996 | Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique |
| ASTM D 2837 : 2013 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2837 : 2004 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.