We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 2794 : 1993 : R2010

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)

    Available format(s): 

    Superseded date:  31-08-2020

    Language(s): 

    Published date:  01-12-2010

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Abstract - (Show below) - (Hide below)

    This test method covers a procedure for rapidly deforming by impact a coating film and its substrate and for evaluating the effect of such deformation.

    Scope - (Show below) - (Hide below)

    1.1 This test method covers a procedure for rapidly deforming by impact a coating film and its substrate and for evaluating the effect of such deformation.

    1.2 This test method should be restricted to testing in only one laboratory when numerical values are used because of the poor reproducibility of the method. Interlaboratory agreement is improved when ranking is used in place of numerical values.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee D 01
    Document Type Test Method
    Product Note Reconfirmed 2010
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM E 1795 : 2017 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
    ASTM D 3730 : 2017 Standard Guide for Testing High-Performance Interior Architectural Wall Coatings
    ASTM D 3794 : 2018 Standard Guide for Testing Coil Coatings
    ASTM F 2408 : 2016 Standard Specification for Ornamental Fences Employing Galvanized Steel Tubular Pickets
    ASTM D 5420 : 2016 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
    ASTM D 6665 : 2009 : R2014 Standard Practice for Evaluation of Aging Resistance of Pre-stressed Prepainted Metal in a Boiling Water Test
    ASTM D 4956 : 2019 Standard Specification for Retroreflective Sheeting for Traffic Control
    ASTM D 3732 : 1982 : R2017 Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings
    ASTM D 8161 : 2017 Standard Test Method for Impact Resistance of Thermoplastic Pavement Marking Materials over a Highway Substrate by Means of a Striker Impacted by a Falling Weight
    ASTM E 2924 : 2014 Standard Practice for Intumescent Coatings
    ASTM E 1797 : 2012 : R2017 : EDT 1 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
    ASTM D 6577 : 2015 Standard Guide for Testing Industrial Protective Coatings
    ASTM D 7230 : 2006 : R2013 Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
    ASTM D 7270 : 2007 : R2013 Standard Guide for Environmental and Performance Verification of Factory-Applied Liquid Coatings
    ASTM A 742/A742M : 2018 Standard Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe
    ASTM D 3451 : 2006 : R2017 Standard Guide for Testing Coating Powders and Powder Coatings
    ASTM D 6905 : 2003 : R2012 Standard Test Method for Impact Flexibility of Organic Coatings
    ASTM D 16 : 2019 Standard Terminology for Paint, Related Coatings, Materials, and Applications
    ASTM F 2589 : 2016 Standard Specification for Ornamental Fences Employing Steel Tubular Pickets
    ASTM A 755/A755M : 2018 Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 823 : 1995 Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels
    ASTM D 609 : 2017 : REDLINE Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products
    ASTM D 1186 : 2001 Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base (Withdrawn 2006)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective