Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 3032 : 2021

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Methods for Hookup Wire Insulation
Available format(s)

Hardcopy , PDF

Superseded date

01-07-2021

Language(s)

English

Published date

19-02-2021

1.1These test methods cover procedures for testing hookup wire.

1.2For the purposes of these test methods, hookup wire insulation includes all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions.

1.3These test methods and their locations are as follows:

Section

Axial Stability (Longitudinal Change) After Thermal Exposure

21

Bondability of Insulation to Potting Compounds

19

Capacitance

9 to 12

Cold Bend Test

26

Concentricity

26

Crush Resistance

20

Dielectric Breakdown Voltage

5

Dimensions

15

Dry-arc Tracking

29

Dynamic Cut-through

22

Fluid Immersion

23

High Temperature Shock

24

Insulation-Continuity Proof Tests

13

Insulation Resistance

6

Partial Discharge (Corona) Inception and Extinction Voltage

25

Relative Thermal Life and Temperature Index

14

Strip Force

27

Surface Resistance

27

Tensile Properties

17

Vertical Flame

18

Vertical Flame Test A

18.5
(Test Method D8354)

Vertical Flame Test B

18.618.11.4

Voltage Rating of Hook-Up Wire

Annex A1

Voltage Withstand Test

8

Wet Arc-tracking

28

1.4The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

1.5This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not, by itself, incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.6Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 12.2.1, 12.4.1.8, 18.1.3, 25.4, and Note 19.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 09
DocumentType
Test Method
Pages
40
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4565 : 2020 Standard Test Methods for Physical and Environmental Performance Properties of <brk/>Insulations and Jackets for Telecommunications Wire and Cable
ASTM D 8354 : 2020 Standard Test Method for Flammability of Electrical Insulating Materials Used for Sleeving or Tubing
ASTM D 8354 : 2021 Standard Test Method for Flammability of Electrical Insulating Materials Intended for Wires or Cables When Burning in a Vertical Configuration
DSCC 23003:2023 WIRE, ELECTRICAL, FLUOROPOLYMER INSULATED, SMOOTH SURFACE, NORMAL, EXTRA HIGH STRENGTH COPPER CONDUCTOR, NICKEL COATED, 260 °C, 600 VOLT

ASTM D 257 : 2014 Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 412 : 2016 : EDT 1 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 412 : 2016 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D 8354 : 2020 Standard Test Method for Flammability of Electrical Insulating Materials Used for Sleeving or Tubing
ASTM D 2303 : 2020 : EDT 1 Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials
ASTM D 8354 : 2021 Standard Test Method for Flammability of Electrical Insulating Materials Intended for Wires or Cables When Burning in a Vertical Configuration
ASTM D 6054 : 1997 : R2004 Standard Practice for Conditioning Electrical Insulating Materials for Testing (Withdrawn 2012)
ASTM D 257 : 2014 : R2021 : EDT 1 Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D 2303 : 2020 Standard Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials

View more information
$176.78
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more