Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

ASTM D 3154 : 2014 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Method for Average Velocity in a Duct (Pitot Tube Method)
Available format(s)

PDF

Language(s)

English

Published date

05-06-2014

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 11.03, 2015 Defines the measurement of the average velocity of a gas stream for the purpose of determining gas flow in a stack, duct, or flue.

1.1This test method describes measurement of the average velocity of a gas stream for the purpose of determining gas flow in a stack, duct, or flue. Although technically complex, it is generally considered the most accurate and often the only practical test method for taking velocity measurements.

1.2This test method is suitable for measuring gas velocities above 3 m/s (10 ft/s).

1.3This test method provides procedures for determining stack gas composition and moisture content.

1.4The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only.

1.5This test method is applicable to conditions where steady-state flow occurs, and for constant fluid conditions, where the direction of flow is normal to the face tube opening of the pitot tube employed in the method. The method cannot be used for direct measurement when cyclonic or swirling flow conditions are present.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 22
DocumentType
Redline
Pages
12
PublisherName
American Society for Testing and Materials
Status
Current

I.S. EN 15429-2:2012 SWEEPERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
UNE-EN 15429-2:2013 Sweepers - Part 2: Performance requirements and test methods
ASTM D 6784 : 2016 : REDLINE Standard Test Method for Elemental, Oxidized, Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired Stationary Sources (Ontario Hydro Method)
ASTM D 3685/D3685M : 2013 : REDLINE Standard Test Methods for Sampling and Determination of Particulate Matter in Stack Gases
DIN EN 15429-2 E : 2013 SWEEPERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
ASTM D 7295 : 2011-03 PRACTICE FOR SAMPLING COMBUSTION EFFLUENTS AND OTHER STATIONARY SOURCES FOR THE SUBSEQUENT DETERMINATION OF HYDROGEN CYANIDE
ASTM D 5835 : 1995 : R2007 Standard Practice for Sampling Stationary Source Emissions for the Automated Determination of Gas Concentrations
ASTM D 4536 : 1996 Standard Test Method for High-Volume Sampling for Solid Particulate Matter and Determination of Particulate Emissions (Withdrawn 2000)
ASTM D 5835 : 1995 : R2013 Standard Practice for Sampling Stationary Source Emissions for the Automated Determination of Gas Concentrations
ASTM D 6060 : 2017 : REDLINE Standard Test Method for Sampling of Process Vents with a Portable Gas Chromatograph
ASTM D 6331 : 2016 : REDLINE Standard Test Method for Determination of Mass Concentration of Particulate Matter from Stationary Sources at Low Concentrations (Manual Gravimetric Method)
ASTM F 1977 : 2004 : R2010 Standard Test Method for Determining Initial, Fractional, Filtration Efficiency of a Vacuum Cleaner System
10/30234205 DC : 0 BS EN 15429-2 - SWEEPERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
ASTM D 5835 : 1995 : R2001 Standard Practice for Sampling Stationary Source Emissions for the Automated Determination of Gas Concentrations
UNI EN 15429-2 : 2013 SWEEPERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
EN 15429-2:2012 Sweepers - Part 2: Performance requirements and test methods
DIN EN 15429-2:2013-03 SWEEPERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
BS EN 15429-2:2012 Sweepers Performance requirements and test methods
09/30194529 DC : 0 BS EN 15429-2 - SWEEPERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS
ASTM D 5835 : 1995 Standard Practice for Sampling Stationary Source Emissions for the Automated Determination of Gas Concentrations
ASTM F 1977 : 2004 : R2017 Standard Test Method for Determining Initial, Fractional, Filtration Efficiency of a Vacuum Cleaner System
ASTM F 1977 : 2004 Standard Test Method for Determining Initial, Fractional, Filtration Efficiency of a Vacuum Cleaner System
ASME PTC19.23 : 1980 PERFORMANCE TEST CODES - PART 23: GUIDANCE MANUAL FOR MODEL TESTING

ASTM D 1071 : 2017 Standard Test Methods for Volumetric Measurement of Gaseous Fuel Samples
ASME PTC19.10 : 1981 PERFORMANCE TEST CODES - SUPPLEMENT ON INSTRUMENTS AND APPARATUS - PART 10: FLUE AND EXHAUST GAS ANALYSES
ASTM D 6522 : 2011 : REDLINE Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers
ASTM E 2251 : 2014 : REDLINE Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
ASTM D 3685/D3685M : 2013 : REDLINE Standard Test Methods for Sampling and Determination of Particulate Matter in Stack Gases
ASTM E 337 : 2015 : REDLINE Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASME PTC 38:1980(R1985) PERFORMANCE TEST CODES - DETERMINING THE CONCENTRATION OF PARTICULATE MATTER IN A GAS STREAM
CFR 50(PTS1-16) : OCT 2017 WILDLIFE AND FISHERIES

View more information
$135.86
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more