Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 3641 : 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
Available format(s)

Hardcopy , PDF

Superseded date

29-05-2021

Language(s)

English

Published date

30-06-2015

1.1This practice covers the general principles to be followed when injection molding test specimens of thermoplastic molding and extrusion materials. This practice is to be used to obtain uniformity in methods of describing the various steps of the injection molding process and to set up uniform methods of reporting these conditions. The exact conditions required to prepare suitable specimens will vary for each plastic material. Any requirements or recommendations in the material specification that differ from this standard take precedence over those in this standard. Always consult the referenced material document for specimen preparation. If no referenced document exists, then consult the material supplier for specimen preparation guidance and note such in the test report.

1.2The methodology presented assumes the use of reciprocating screw injection molding machines.

1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:This practice is equivalent to the following parts of ISO 294: Plastics—Injection Moulding of Test Specimens of Thermoplastic Materials; 294-1: Part 1—General Principles and Multipurpose Test Specimens (ISO Type A Mould) and Bars (ISO Type B Mould); ISO 294-2: Part 2—Small Tensile Bars (ISO Type C Mould); ISO 294-3: Part 3—Plates (ISO Type D Moulds).

Committee
D 20
DocumentType
Standard Practice
Pages
10
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4101 : 2017 : EDT 1 Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
ASTM D 706 : 2020 Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)
ASTM D 6394 : 2021 : REV A Standard Classification System for and Basis for Specification for Sulfone Plastics (SP)
ASTM D 4066 : 2013 : R2019 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 5204 : 2019 Standard Classification System and Basis for Specification for Polyamide-Imide (PAI) Molding and Extrusion Materials
ASTM D 6358 : 2019 : EDT 1 Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods
ASTM D 5990 : 2020 : REV A Standard Classification System and Basis for Polyketone Injection Molding and Extrusion Materials (PK)
ASTM D 787 : 2018 Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds
ASTM D 5592 : 1994 : R2018 Standard Guide for Material Properties Needed in Engineering Design Using Plastics
ASTM D 6394 : 2014 Standard Specification for Sulfone Plastics (SP)
ASTM D 3965 : 2016 Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
ASTM D 4673 : 2016 Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials
ASTM D 955 : 2008 : R2014 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
ASTM D 5336 : 2015 : REV A Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material
ASTM D 3012 : 2019 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven
ASTM D 4634 : 2016 Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)
ASTM D 6835 : 2017 Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE)
ASTM D 256 : 2010 : R2018 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM F 2617 : 2015 Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry
ASTM D 4203 : 2017 Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials
ASTM D 3419 : 2012 : R2019 Standard Practice for In-Line Screw-Injection Molding Test Specimens From Thermosetting Compounds
ASTM D 4067 : 2016 Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
ASTM D 5138 : 2016 Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)
ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
ASTM D 706 : 2015 Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)
ASTM D 6339 : 2011 : R2019 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)
ASTM D 707 : 2015 Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)
ASTM D 5205 : 2016 Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
ASTM D 788 : 2016 Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds
ASTM D 1562 : 2015 Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)

ASTM D 6110 : 2006 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 6110 : 2004 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 6110 : 2002 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 1525 : 2017 : EDT 1 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 6110 : 2008 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 6110 : 2004 : EDT 1 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 6110 : 2010 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 1525 : 2017 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 1525 : 2000 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 1525 : 2006 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 1525 : 1987 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 6110 : 2017 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 1525 : 2009 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 6110 : 2005 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 6110 : 2005 : REV A Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 6110 : 1997 Standard Test Methods for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
ASTM D 1525 : 2007 Standard Test Method for Vicat Softening Temperature of Plastics
ASTM D 6110 : 2018 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more