We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 3675 : 2021 : REV A

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source

    Available format(s):  Hardcopy, PDF

    Superseded date:  28-04-2022

    Language(s):  English

    Published date:  27-04-2021

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This is a fire test response standard.

    1.2This test method describes the measurement of surface flammability of flexible cellular materials.

    1.3This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not, by itself, incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

    1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

    1.6Specific information about hazards is given in Section 7.

    Note 1:There is no known ISO equivalent to this standard.

    1.7The values stated in SI units are to be regarded as the standard. The values stated in inch-pound units, in parentheses, are for information only and are approximations (see also IEEE/ASTM SI-10).

    1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee D 20
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM F 1534 : 2016 Standard Test Method for Determining Changes in Fire-Test-Response Characteristics of Cushioning Materials After Water Leaching
    ASTM E 162 : 2016 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
    ASTM D 3453 : 2020 Standard Specification for Flexible Cellular Materials—Urethane for Furniture and Automotive Cushioning, Bedding, and Similar Applications
    ASTM E 2061 : 2020 Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles
    ASTM F 1870 : 2016 Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities
    ASTM E 3020 : 2016 : REV A Standard Practice for Ignition Sources
    ASTM D 3574 : 2017 Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams
    ASTM C 1482 : 2017 Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
    ASTM E 176 : 2021 : REV A Standard Terminology of Fire Standards
    ASTM E 162 : 2021 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM E 1546 : 2015 Standard Guide for Development of Fire-Hazard-Assessment Standards
    ASTM E 162 : 2021 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
    ASTM E 176 : 2018 : REV A : EDT 1 Standard Terminology of Fire Standards
    ASTM E 456 : 2013 : REV A : R2017 : EDT 5 Standard Terminology Relating to Quality and Statistics
    ASTM E 84 : 2021 Standard Test Method for Surface Burning Characteristics of Building Materials
    ASTM E 84 : 2021 : REV A Standard Test Method for Surface Burning Characteristics of Building Materials
    ASTM E 176 : 2021 Standard Terminology of Fire Standards
    ASTM E 176 : 2018 : REV A : EDT 2 Standard Terminology of Fire Standards
    ASTM E 1546 : 2021 Standard Guide for Development of Fire-Hazard-Assessment Standards
    ASTM E 456 : 2013 : REV A : R2017 : EDT 4 Standard Terminology Relating to Quality and Statistics
    ASTM E 456 : 2013 : REV A : R2017 : EDT 6 Standard Terminology Relating to Quality and Statistics
    ASTM E 176 : 2021 : REV A Standard Terminology of Fire Standards
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective