We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 3801 : 2020

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position

    Available format(s):  Hardcopy, PDF

    Superseded date:  16-09-2020

    Language(s):  English

    Published date:  01-02-2020

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This fire-test-response standard covers a small-scale laboratory procedure for determining comparative burning characteristics of solid-plastic material, using a 20-mm (50W) premixed flame applied to the base of specimens held in a vertical position.

    Note 1:This test method and the 20 mm (50W) Vertical Burning Test (V-0, V-1, or V-2) of ANSI/UL 94 are equivalent.

    Note 2:This test method and Test Method B of IEC 60695–11–10 are equivalent. IEC 60695–11–10 has replaced ISO 1210.

    Note 3:For additional information on materials that burn up to the holding clamp by this test method, see Test Method D635. For test methods of flexible plastics in the form of thin sheets and film, see Test Method D4804. For additional information on comparative burning characteristics and resistance to burn-through, see Test Method D5048.

    1.2This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standards applicable to such equipment.

    1.3The classification system described in the appendix is intended for quality assurance and the preselection of component materials for products.

    1.4It is possible that this test is applicable to nonmetallic materials other than plastics. Such application is outside the scope of this technical committee.

    1.5This test method does not cover plastics when used for building construction, finishing or contents such as wall and floor coverings, furnishings, decorative objects etc. In addition, the fire resistance (in terms of an hourly rating), flame spread, smoke characterization and heat release rate are not evaluated by this test. Other fire tests exist and shall be used to evaluate the flammability of materials in these intended end use product configuration.

    1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.7This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

    1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.9This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee D 20
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 5025 : 2020 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
    ASTM D 4804 : 2020 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
    ASTM D 8065/D8065M : 2016 Standard Classification System and Basis for Specification for Specifying Plastic Films
    ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
    ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
    ASTM D 5336 : 2015 : REV A Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material
    ASTM D 635 : 2018 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
    ASTM D 5048 : 2020 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
    ASTM D 1593 : 2019 Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
    ASTM D 6394 : 2014 Standard Specification for Sulfone Plastics (SP)
    ASTM D 4976 : 2012 : REV A Standard Specification for Polyethylene Plastics Molding and Extrusion Materials

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 4804 : 2019 : REV A Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
    ASTM D 5025 : 2020 : REV A Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
    ASTM D 5025 : 2012 : EDT 1 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
    ASTM D 5048 : 2019 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective