ASTM D 4477 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
Available format(s)
Hardcopy , PDF
Superseded date
05-11-2021
Language(s)
English
Published date
18-05-2016
1.1This specification establishes requirements and test methods for the materials, dimensions, camber, impact strength, expansion, and appearance of extruded single-wall soffit manufactured from rigid (unplasticized) PVC compound. Methods of indicating compliance with this specification are also provided.
1.2The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.3Rigid (unplasticized) poly(vinyl chloride) (PVC) siding is covered in Specification D3679.
1.4Soffit produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.
Note 1:Information with regard to soffit maintenance shall be obtained from the manufacturer.
1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6The following precautionary caveat pertains to the test method portion only, Section 6 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 2:There is no known ISO equivalent to this standard.
| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 3679 : 2021 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4756 : 2015 : R2021 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit (Withdrawn 2023) |
| ASTM E 2266 : 2011 : R2019 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
| ASTM D 4803 : 2018 | Standard Test Method for Predicting Heat Buildup in PVC Building Products |
| ASTM E 2266 : 2011 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
| ASTM D 4756 : 2015 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM D 3679 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 5947 : 1996 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 3679 : 2006 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 2244 : 2021 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM E 1753 : 2001 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
| ASTM D 4226 : 2005 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 2244 : 2015 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 4756 : 2002 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM E 1753 : 1995 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
| ASTM D 5947 : 2002 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM E 1753 : 2019 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
| ASTM D 4756 : 2013 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM D 2244 : 2011 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2457 : 2008 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 4226 : 2019 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 2244 : 2009 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 4756 : 1996 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM D 5947 : 2011 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 2244 : 2002 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3679 : 2003 : EDT 2 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2008 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM E 1753 : 2018 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
| ASTM D 4756 : 2015 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2244 : 2015 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 2009 : REV B | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2244 : 2002 : EDT 1 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3679 : 2001 : REV B | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2244 : 2015 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM E 1753 : 2018 : REV A | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
| ASTM D 3679 : 2002 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3679 : 2009 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2004 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM E 1753 : 2013 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
| ASTM D 5947 : 2006 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 2457 : 2013 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 2244 : 2014 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 3679 : 2004 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2009 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 2244 : 2005 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 4756 : 2003 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM D 3679 : 2017 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2013 | Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding |
| ASTM D 4226 : 2010 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2011 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 1999 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2457 : 1997 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 3679 : 2003 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2244 : 2007 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 5947 : 2003 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4226 : 2016 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2021 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2004 : REV A : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 5947 : 2001 : EDT 1 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 3679 : 2005 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2002 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4756 : 2002 : REV A | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4226 : 2000 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 4756 : 2006 | Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit |
| ASTM D 2457 : 2003 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 2244 : 2009 : REV A | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D 2244 : 1993 : R2000 | Standard Test Method for Calculation of Color Differences From Instrumentally Measured Color Coordinates |
| ASTM D 3679 : 2001 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 3679 : 2003 : EDT 1 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM E 1753 : 2004 | Standard Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint Films |
| ASTM D 2457 : 2021 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 2457 : 2008 : EDT 1 | Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D 3679 : 2001 : REV C | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 4226 : 2009 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2001 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
| ASTM D 4226 : 2011 | Standard Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products |
| ASTM D 3679 : 2006 : REV A | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding |
$108.03
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.