Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 4625 : 2016 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Middle Distillate Fuel Storage Stability at 43 °C (110 °F)
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2021

Language(s)

English

Published date

22-02-2018

1.1This test method covers a method for evaluating the inherent storage stability of distillate fuels having flash points above 38 °C (100 °F), by Test Methods D93, and 90 % distilled points below 340 °C (644 °F), by Test Method D86.

Note 1:ASTM specification fuels falling within the scope of this test method are Specification D396, Grade Nos. 1 and 2; Specification D975, Grades 1-D and 2-D; and Specification D2880, Grades 1-GT and 2-GT.

1.2This test method is not suitable for quality control testing but, rather it is intended for research use to shorten storage time relative to that required at ambient storage temperatures.

1.3Appendix X1 presents additional information about storage stability and the correlation of Test Method D4625 results with sediment formation in actual field storage.

1.4The values given in SI units are to be regarded as the standard.

1.4.1Exception—The values in parentheses are for information only.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Test Method
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 8181 : 2019 Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils
ASTM D 6748 : 2002 : REV A : R2017 Standard Test Method for Determination of Potential Instability of Middle Distillate Fuels Caused by the Presence of Phenalenes and Phenalenones (Rapid Method by Portable Spectrophotometer)
ASTM D 1655 : 2019 Standard Specification for Aviation Turbine Fuels
ASTM D 2274 : 2014 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
ASTM D 6468 : 2008 : R2019 Standard Test Method for High Temperature Stability of Middle Distillate Fuels
ASTM D 7566 : 2019 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 7566 : 2021 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 2274 : 2014 : R2019 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)

ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4057 : 1995 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 4177 : 2016 : EDT 1 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 396 : 2020 Standard Specification for Fuel Oils
ASTM D 4177 : 1995 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4057 : 2012 : R2018 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 396 : 1998 Standard Specification for Fuel Oils
ASTM D 2880 : 2000 Standard Specification for Gas Turbine Fuel Oils
ASTM D 975 : 2019 : REV B Standard Specification for Diesel Fuel
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM D 4057 : 1981 : EDT 2 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 2880 : 1990 Standard Specification for Gas Turbine Fuel Oils
ASTM D 975 : 2021 Standard Specification for Diesel Fuel
ASTM D 2880 : 2013 Standard Specification for Gas Turbine Fuel Oils
ASTM D 2880 : 2013 : REV A Standard Specification for Gas Turbine Fuel Oils
ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
ASTM D 975 : 2020 : REV C Standard Specification for Diesel Fuel
ASTM D 2880 : 2018 Standard Specification for Gas Turbine Fuel Oils
ASTM D 4057 : 2006 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 2880 : 1998 Standard Specification for Gas Turbine Fuel Oils
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM D 4177 : 2015 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 2880 : 2020 Standard Specification for Gas Turbine Fuel Oils
ASTM D 4057 : 2012 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 2880 : 2003 : R2010 Standard Specification for Gas Turbine Fuel Oils
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM D 4177 : 1995 : R2010 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 2880 : 2015 Standard Specification for Gas Turbine Fuel Oils
ASTM D 4177 : 1995 : R2000 Standard Practice for Automatic Sampling of Peroleum and Petroleum Products
ASTM D 396 : 2021 Standard Specification for Fuel Oils
ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 396 : 2009 Standard Specification for Fuel Oils
ASTM D 2880 : 2014 Standard Specification for Gas Turbine Fuel Oils
ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
ASTM D 2880 : 2013 : REV B Standard Specification for Gas Turbine Fuel Oils
ASTM D 4177 : 2016 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 4177 : 1995 : R2005 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 2880 : 1996 Standard Specification for Gas Turbine Fuel Oils
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 2880 : 2018 : REV A Standard Specification for Gas Turbine Fuel Oils
ASTM D 4057 : 1995 : R2000 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water
ASTM D 4177 : 2015 : REV A Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
ASTM D 4057 : 2006 : R2011 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 2880 : 1978 Standard Specification for Gas Turbine Fuel Oils
ASTM D 2880 : 2003 Standard Specification for Gas Turbine Fuel Oils
ASTM D 2880 : 2014 : REV A Standard Specification for Gas Turbine Fuel Oils

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more