Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 5813 : 2004 : R2018

Current
Current

The latest, up-to-date edition.

Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-10-2018

1.1This specification covers cured-in-place thermosetting resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm) equivalent diameter, for use in gravity flow systems for conveying sanitary sewage, storm water, and certain industrial wastes. This specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and cure of a resin-impregnated fabric liner.

1.2This specification can also be extended to cover manholes, pump stations, wetwells, vaults, storage tanks, and other similar structures where a cured in place liner using thermosetting resin is applicable.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Note 1:There are no ISO standards covering the primary subject matter of this specification.

1.4The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM F 2994 : 2018 Standard Practice for Utilization of Mobile, Automated Cured-In-Place Pipe (CIPP) Impregnation Systems
ASTM F 1216 : 2016 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM F 1743 : 2017 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM F 2019 : 2011 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM F 2561 : 2017 Standard Practice for Rehabilitation of a Sewer Service Lateral and Its Connection to the Main Using a One Piece Main and Lateral Cured-in-Place Liner
ASTM F 2599 : 2016 Standard Practice for The Sectional Repair of Damaged Pipe By Means of An Inverted Cured-In-Place Liner

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 883 : 2023 Standard Terminology Relating to Plastics
ASTM F 2019 : 2020 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
ASTM D 4814 : 2016 : REV C Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM D 4814 : 2015 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 883 : 2024 Standard Terminology Relating to Plastics
ASTM F 1743 : 2021 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM D 4814 : 2018 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 883 : 2022 Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM D 4814 : 2016 : REV : EDT 0 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2023 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 543 : 2021 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM F 1216 : 1998 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 4814 : 2016 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 3681 : 2018 Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
ASTM D 4814 : 2022 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2021 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 3567 : 2017 : R2022 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 4814 : 2021 : REV C Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2023 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2016 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM F 1743 : 2008 : R2016 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM F 1216 : 2021 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 3681 : 2023 Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
ASTM D 1682 : 1964 : R1975 : EDT 1 Standard Methods of Test for Breaking Load and Elongation of Textile Fabrics (Withdrawn 1992)
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 4814 : 2016 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 543 : 2020 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 4814 : 1992 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2015 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM F 412 : 2023 Standard Terminology Relating to Plastic Piping Systems
ASTM D 3681 : 1996 Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
ASTM D 3567 : 1997 Standard Practice for Determining Dimensions of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM D 4814 : 2018 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 695 : 2015 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM D 4814 : 2016 : REV D Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2021 : REV A Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM F 2019 : 2000 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic (GRP) Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM F 1743 : 2022 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM D 3567 : 2017 Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
ASTM F 1743 : 1996 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM D 695 : 2023 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM F 2019 : 2022 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Pulled in Place Installation of Glass Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the UV-Light Curing Method
ASTM D 4814 : 2018 : REV C Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 4814 : 2021 : REV B Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 638 : 2022 Standard Test Method for Tensile Properties of Plastics
ASTM F 1216 : 2022 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube

View more information
$90.04
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more