Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 638 : 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Tensile Properties of Plastics
Available format(s)

Hardcopy , PDF

Superseded date

25-07-2022

Language(s)

English

Published date

12-03-2015

This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.

1.1This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed.

1.2This test method is applicable for testing materials of any thickness up to 14 mm (0.55 in.). However, for testing specimens in the form of thin sheeting, including film less than 1.0 mm (0.04 in.) in thickness, ASTM standard D882 is the preferred test method. Materials with a thickness greater than 14 mm (0.55 in.) shall be reduced by machining.

1.3This test method includes the option of determining Poisson's ratio at room temperature.

Note 1:This standard and ISO 527-1 address the same subject matter, but differ in technical content.

Note 2:This test method is not intended to cover precise physical procedures. It is recognized that the constant rate of crosshead movement type of test leaves much to be desired from a theoretical standpoint, that wide differences may exist between rate of crosshead movement and rate of strain between gage marks on the specimen, and that the testing speeds specified disguise important effects characteristic of materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens, which are permitted by these procedures, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed.

Note 3:This test method may be used for testing phenolic molded resin or laminated materials. However, where these materials are used as electrical insulation, such materials should be tested in accordance with Test Methods D229 and Test Method D651.

Note 4:For tensile properties of resin-matrix composites reinforced with oriented continuous or discontinuous high modulus >20-GPa (>3.0 × 106-psi) fibers, tests shall be made in accordance with Test Method D3039/D3039M.

1.4Test data obtained by this test method have been found to be useful in engineering design. However, it is important to consider the precautions and limitations of this method found in Note 2 and Section 4 before considering these data for engineering design.

1.5The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 20
DocumentType
Test Method
Pages
17
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 3373 : 2021 Standard Specification for Polyethylene (PE) Electrofusion Fittings for Outside Diameter Controlled Crosslinked Polyethylene (PEX) Pipe
ASTM D 3935 : 2021 Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material
ASTM F 2225 : 2015 : R2020 Standard Safety Specification for Consumer Trampoline Enclosures
ASTM F 1804 : 2021 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
ASTM D 5592 : 1994 : R2018 Standard Guide for Material Properties Needed in Engineering Design Using Plastics
ASTM D 2239 : 2021 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
ASTM D 4634 : 2016 Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)
ASTM F 1743 : 2021 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
ASTM C 1173 : 2022 Standard Specification for Flexible Transition Couplings for Underground Piping Systems
ASTM F 1871 : 2020 Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation
ASTM D 2287 : 2019 Standard Classification System and Basis for Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds
ASTM F 3034 : 2021 Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE)
ASTM D 3159 : 2022 Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials
ASTM D 706 : 2020 Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)
ASTM D 5364 : 2014 : R2019 Standard Guide for Design, Fabrication, and Erection of Fiberglass Reinforced (FRP) Plastic Chimney Liners with Coal-Fired Units
ASTM D 4802 : 2016 Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet
ASTM D 4895 : 2018 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion
ASTM F 3219 : 2019 Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
ASTM F 2418 : 2019 Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
ASTM F 2971 : 2013 : R2021 Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing
ASTM E 2254 : 2018 Standard Test Method for Storage Modulus Calibration of Dynamic Mechanical Analyzers
ASTM D 5045 : 2014 Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials
ASTM D 6098 : 2016 Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC)
ASTM D 3032 : 2021 : REV A Standard Test Methods for Hookup Wire Insulation
ASTM D 2513 : 2020 Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
ASTM D 2609 : 2021 Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
ASTM F 3536 : 2022 Standard Specification for PE and PP Mechanical Fittings for use on NPS 3 or Smaller Cold-water Service Polyethylene (PE) or Crosslinked Polyethylene (PEX) Pipe or Tubing
ASTM D 5083 : 2017 Standard Test Method for Tensile Properties of Reinforced Thermosetting Plastics Using Straight-Sided Specimens
ASTM D 6392 : 2012 : R2018 Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods
ASTM F 2767 : 2018 Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution
ASTM D 3105 : 2017 Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM F 1635 : 2016 Standard Test Method for <emph type="bdit">in vitro</emph> Degradation Testing of Hydrolytically Degradable Polymer Resins and Fabricated Forms for Surgical Implants
ASTM D 5336 : 2021 Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials
ASTM D 4549 : 2015 : R2021 Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS)
ASTM F 2026 : 2017 Standard Specification for Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications
ASTM F 790 : 2018 Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures
ASTM D 5948 : 2005 : R2020 Standard Specification for Molding Compounds, Thermosetting
ASTM D 4000 : 2020 Standard Classification System for Specifying Plastic Materials
ASTM F 2759 : 2019 Standard Guide for Assessment of the Ultra-High Molecular Weight Polyethylene (UHMWPE) Used in Orthopedic and Spinal Devices
ASTM D 1562 : 2015 Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)
ASTM F 2176 : 2017 Standard Specification for Mechanical Couplings Used on Polyethylene Conduit, Duct and Innerduct
ASTM D 1623 : 2017 Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics
ASTM D 4396 : 2015 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications
ASTM F 3333 : 2020 Standard Specification for Chopped Carbon Fiber Reinforced (CFR) Polyetheretherketone (PEEK) Polymers for Surgical Implant Applications
ASTM F 3508 : 2021 : REV A Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)
ASTM D 3517 : 2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe
ASTM F 2921 : 2013 : R2019 Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies
ASTM F 1588 : 1996(R2019) Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM F 2817 : 2013 : R2019 Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair
ASTM D 7745 : 2019 Standard Practice for Testing Pultruded Composites
ASTM D 6394 : 2021 : REV A Standard Classification System for and Basis for Specification for Sulfone Plastics (SP)
ASTM D 3748 : 2014 : R2019 Standard Practice for Evaluating High-Density Rigid Cellular Plastics
ASTM G 178 : 2016 Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique
ASTM F 1988 : 1999(R2020) Standard Performance Requirements for Plastic Chaise Lounges, With or Without Moving Arms, With Adjustable Backs, for Outdoor Use
ASTM D 7292 : 2018 Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI)
ASTM F 1563 : 2001 : R2019 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 381 : 2016 Standard Safety Specification for Components, Assembly, Use, and Labeling of Consumer Trampolines
ASTM D 3308 : 2012 : R2022 Standard Specification for PTFE Resin Skived Tape
ASTM D 6263 : 2022 Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC)
ASTM F 2435 : 2022 Standard Specification for Steel Reinforced Polyethylene (PE) Corrugated Pipe
ASTM D 1039 : 2016 : R2022 Standard Test Methods for Glass-Bonded Mica Used as Electrical Insulation
ASTM F 2376 : 2022 Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems
ASTM D 4216 : 2022 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds
ASTM F 2160 : 2022 Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD)
ASTM D 2996 : 2017 Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
ASTM D 7272 : 2006 : R2018 Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Premanufactured Taped Methods
ASTM F 2945 : 2018 Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
ASTM D 3965 : 2021 Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
ASTM D 4673 : 2016 Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials
ASTM D 3275 : 2018 Standard Classification System for E-CTFE-Fluoroplastic Molding, Extrusion, and Coating Materials
ASTM D 4976 : 2012 : REV A : R2020 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM A 1113/A1113M : 2020 : EDT 1 Standard Specification for Corrugated Steel Structural Plate, Polymer-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches
ASTM F 561 : 2019 Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids
ASTM D 6272 : 2017 : EDT 1 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM F 2619/F2619M : 2020 Standard Specification for High-Density Polyethylene (PE) Line Pipe
ASTM F 2790 : 2010 : R2019 : EDT 1 Standard Practice for Static and Dynamic Characterization of Motion Preserving Lumbar Total Facet Prostheses
ASTM D 7408 : 2012 : R2020 Standard Specification for Non-Reinforced PVC (Polyvinyl Chloride) Geomembrane Seams
ASTM D 3841 : 2021 Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
ASTM C 881/C881M : 2020 : REV A Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete
ASTM D 6262 : 2017 Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK)
ASTM E 2831/E2831M : 2011 : R2018 Standard Guide for Deployment of Blast Resistant Trash Receptacles in Crowded Places
ASTM D 4762 : 2018 Standard Guide for Testing Polymer Matrix Composite Materials
ASTM F 639 : 2009 : R2015 Standard Specification for Polyethylene Plastics for Medical Applications
ASTM D 6712 : 2017 Standard Specification for Ultra-High-Molecular-Weight Polyethylene (UHMW-PE) Solid Plastic Shapes
ASTM F 2928 : 2018 Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods
ASTM D 3916 : 2008 : R2016 Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced<brk /> Plastic Rod
ASTM D 5224 : 2012 : R2019 Standard Practice for Compression Molding Test Specimens of Thermosetting Molding Compounds
ASTM D 6338 : 2017 Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods
ASTM D 5138 : 2016 Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)
ASTM F 2097 : 2020 Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products
ASTM F 451 : 2021 Standard Specification for Acrylic Bone Cement
ASTM F 711 : 2017 Standard Specification for Fiberglass-Reinforced Plastic (FRP) Rod and Tube Used in Live Line Tools
ASTM D 4801 : 2008 : R2016 Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater
ASTM D 3754 : 2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
ASTM F 1533 : 2020 Standard Specification for Deformed Polyethylene (PE) Liner
ASTM F 852/F852M : 2022 Standard Specification for Portable Gasoline, Kerosene, and Diesel Containers for Consumer Use
ASTM D 2902 : 2021 Standard Specification for Fluoropolymer Resin Heat-Shrinkable Tubing for Electrical Insulation
ASTM F 1858 : 1998 : R2020 Standard Performance Requirements for Multipositional Plastic Chairs with Adjustable Backs or Reclining Mechanisms for Outdoor Use
ASTM F 3087 : 2015 Standard Specification for Acrylic Molding Resins for Medical Implant Applications
ASTM F 2562/F2562M : 2015 : R2019 Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage
ASTM D 8366 : 2021 : REV A Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF
ASTM D 5436 : 2015 : R2020 Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes
ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
ASTM F 2896 : 2011 : R2017 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
ASTM D 6456 : 2010 : R2018 Standard Specification for Finished Parts Made from Polyimide Resin
ASTM F 3524/F3524M : 2021 Standard Specification for Polyamide-12 (PA12) Line Pipe
ASTM D 3368 : 2017 : R2022 Standard Specification for FEP Sheet and Film
ASTM D 1822 : 2021 Standard Test Method for Determining the Tensile-Impact Resistance of Plastics
ASTM F 1924 : 2019 Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
ASTM F 480 : 2014 : R2022 Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
ASTM D 3262 : 2020 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe
ASTM F 2600 : 2009 : R2018 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing
ASTM G 210 : 2013 : R2018 Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus
ASTM F 1867 : 2006 : R2020 Standard Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation
ASTM F 3525/F3525M : 2021 Standard Specification Fabricated Fittings of Crosslinkable Polyethylene (CX-PE)
ASTM F 1606 : 2019 Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner
ASTM D 6324 : 2011 : R2017 Standard Specification for Male Condoms Made from Polyurethane
ASTM F 641 : 2009 : R2014 Standard Specification for Implantable Epoxy Electronic Encapsulants
ASTM D 4067 : 2021 Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
ASTM D 5205 : 2016 Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
ASTM D 2122 : 2016 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 4097 : 2019 Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
ASTM D 787 : 2018 Standard Specification for Ethyl Cellulose Molding and Extrusion Compounds
ASTM F 3378/F3378M : 2022 Standard Specification for Crosslinkable Polyethylene (CX-PE) Pipe
ASTM D 6041 : 2018 Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
ASTM F 702 : 2018 Standard Specification for Polysulfone Resin for Medical Applications
ASTM E 2771 : 2011 : R2019 Standard Terminology for Homeland Security Applications
ASTM C 722 : 2018 Standard Specification for Chemical-Resistant Monolithic Floor Surfacings
ASTM D 695 : 2015 Standard Test Method for Compressive Properties of Rigid Plastics
ASTM F 2509 : 2015 : R2019 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing
ASTM D 4101 : 2017 : EDT 1 Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
ASTM F 3507 : 2021 Standard Practice for Butt-Fusion Joining of Crosslinkable Polyethylene (CX-PE) Pipe and Tubing
ASTM D 3222 : 2021 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
ASTM D 2647 : 2018 Standard Specification for Crosslinkable Ethylene Plastics
ASTM D 3295 : 2020 Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing
ASTM D 2633 : 2021 Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable
ASTM D 7056 : 2007 : R2018 Standard Test Method for Determining the Tensile Shear Strength of Prefabricated Bituminous Geomembrane Seams
ASTM F 3181 : 2016 Standard Test Method for The Un-notched, Constant Ligament Stress Crack Test (UCLS) for HDPE Materials Containing Post- Consumer Recycled HDPE
ASTM F 1055 : 2016 : REV A Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
ASTM D 3307 : 2021 Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
ASTM D 1043 : 2016 Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test
ASTM F 2902 : 2016 : EDT 1 Standard Guide for Assessment of Absorbable Polymeric Implants
ASTM C 1594 : 2011 : R2017 Standard Specification for Polyimide Rigid Cellular Thermal Insulation
ASTM D 3013 : 2013 : R2021 Standard Specification for Epoxy Molding Compounds
ASTM D 6713 : 2021 Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF)
ASTM F 2145 : 2013 : R2018 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
ASTM D 2294 : 1996 : R2016 Standard Test Method for Creep Properties of Adhesives in Shear by Tension Loading (Metal-to-Metal)
ASTM F 450 : 2013 : R2019 Standard Test Methods for Vacuum Cleaner Hose—Durability and Reliability (Plastic)
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM F 1309 : 1998 : R2018 Standard Practice for Installation Procedures for Fitting Chocks to Marine Machinery Foundations
ASTM D 4093 : 1995 : R2014 Standard Test Method for Photoelastic Measurements of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials
ASTM D 5989 : 2018 Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA)
ASTM F 1973 : 2021 Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
ASTM D 3485 : 2015 Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC)
ASTM D 4434/D4434M : 2021 Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
ASTM F 2820 : 2012 : R2021 : EDT 1 Standard Specification for Polyetherketoneketone (PEKK) Polymers for Surgical Implant Applications
ASTM F 645 : 2018 : REV B Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
ASTM F 3183 : 2021 Standard Practice for Guided Side Bend Evaluation of Polyethylene Pipe Butt Fusion Joint
ASTM F 2306/F2306M : 2021 Standard Specification for 300 mm to 1500 mm [12 in. to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Non-Pressure Gravity-Flow Storm Sewer and Subsurface Drainage Applications
ASTM D 4565 : 2020 Standard Test Methods for Physical and Environmental Performance Properties of <brk/>Insulations and Jackets for Telecommunications Wire and Cable
ASTM E 2740 : 2012 : R2018 Standard Specification for Trash Receptacles Subjected to Blast Resistance Testing
ASTM D 229 : 2019 : EDT 1 Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation
ASTM D 6339 : 2011 : R2019 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)
ASTM D 3350 : 2021 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM F 1838 : 2019 Standard Performance Requirements for Adult and Children’s Plastic Chairs for Outdoor Use
ASTM F 602 : 2009 : R2015 Standard Criteria for Implantable Thermoset Epoxy Plastics
ASTM F 2764/F2764M : 2019 Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications
ASTM C 1349 : 2017 Standard Specification for Architectural Flat Glass Clad Polycarbonate
ASTM D 7275 : 2007 : R2018 Standard Test Method for Tensile Properties of Bituminous Geomembranes (BGMs)
ASTM E 2639 : 2012 : R2018 Standard Test Method for Blast Resistance of Trash Receptacles
ASTM D 3840 : 2019 Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications
ASTM D 2295 : 1996 : R2016 Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading at Elevated Temperatures (Metal-to-Metal)
ASTM C 582 : 2009 : R2016 Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment
ASTM D 7472 : 2019 Standard Specification for EFEP-Fluoropolymer Molding and Extrusion Materials
ASTM F 2881/F2881M : 2021 : EDT 1 Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
ASTM F 755 : 2019 Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
ASTM D 7194 : 2019 Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE)
ASTM D 7027 : 2020 Standard Test Method for Evaluation of Scratch Resistance of Polymeric Coatings and Plastics Using an Instrumented Scratch Machine
ASTM D 3929 : 2003 : R2015 Standard Test Method for Evaluating Stress Cracking of Plastics by Adhesives Using the Bent-Beam Method
ASTM D 883 : 2020 : REV B Standard Terminology Relating to Plastics
ASTM D 7082 : 2021 Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe
ASTM F 1948 : 2020 Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing
ASTM F 997 : 2018 Standard Specification for Polycarbonate Resin for Medical Applications
ASTM D 8436 : 2022 Standard Specification for Fluoropolymer-based Materials for Use for Encapsulation of Downhole Cable
ASTM D 7471 : 2019 Standard Specification for CPT-Fluoropolymer Molding and Extrusion Materials
ASTM F 2720/F2720M : 2020 Standard Specification for Glass Fiber Reinforced Polyethylene (PE-GF) Spiral Wound Large Diameter Pipe
ASTM A 974 : 1997 : R2021 Standard Specification for Welded Wire Fabric Gabions and Gabion Mattresses (Metallic-Coated or Polyvinyl Chloride (PVC) Coated)
ASTM D 1248 : 2016 Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
ASTM D 8427 : 2021 Standard Specification for Rigid Poly Vinyl Chloride (PVC) Exterior Profiles Used for Sheet Piling
ASTM D 6261 : 2014 : R2022 Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
ASTM D 790 : 2017 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM F 2331 : 2011 : R2021 Standard Test Method for Determining Chemical Compatibility of Substances in Contact with Thermoplastic Pipe and Fittings Materials
ASTM F 2785 : 2021 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
ASTM D 2990 : 2017 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 3641 : 2021 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 5977 : 2015 Standard Specification for High Load Rotational Spherical Bearings for Bridges and Structures
ASTM F 3091/F3091M : 2014 : R2021 Standard Specification for Powder Bed Fusion of Plastic Materials
ASTM D 2105 : 2001 : R2019 Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
ASTM C 1482 : 2017 Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
ASTM D 4020 : 2018 Standard Specification for Ultra-High-Molecular-Weight Polyethylene Molding and Extrusion Materials
ASTM D 6100 : 2017 Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM)
ASTM D 3826 : 2018 Standard Practice for Determining Degradation End Point in Degradable Polyethylene and Polypropylene Using a Tensile Test
ASTM D 5747/D5747M : 2021 Standard Practice for Tests to Evaluate the Chemical Resistance of Geomembranes to Liquids
ASTM C 143/C143M : 2020 Standard Test Method for Slump of Hydraulic-Cement Concrete
ASTM D 5813 : 2004 : R2018 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ASTM D 6214/D6214M : 1998 : R2022 Standard Test Method for Determining the Integrity of Field Seams Used in Joining Geomembranes by Chemical Fusion Methods
ASTM F 3274 : 2021 Standard Guide for Testing and Characterization of Alginate Foam Scaffolds Used in Tissue-Engineered Medical Products (TEMPs)
ASTM F 3510 : 2021 Standard Guide for Characterizing Fiber-Based Constructs for Tissue-Engineered Medical Products
ASTM G 21 : 2015 : R2021 : EDT 1 Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
ASTM F 2947/F2947M : 2021 : REV A Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM D 1708 : 2018 Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D 5990 : 2020 : REV A Standard Classification System and Basis for Polyketone Injection Molding and Extrusion Materials (PK)
ASTM C 647 : 2019 Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
ASTM D 5575 : 2018 Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
ASTM D 2737 : 2021 Standard Specification for Polyethylene (PE) Plastic Tubing
ASTM D 6693/D6693M : 2020 Standard Test Method for Determining Tensile Properties of Nonreinforced Polyethylene and Nonreinforced Flexible Polypropylene Geomembranes
ASTM E 2634 : 2018 Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
ASTM D 2116 : 2016 : R2021 Standard Specification for FEP Resin Molding and Extrusion Materials
ASTM D 4203 : 2017 Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials
ASTM F 648 : 2021 Standard Specification for Ultra-High-Molecular-Weight Polyethylene Powder and Fabricated Form for Surgical Implants
ASTM G 114 : 2021 Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service
ASTM F 1216 : 2021 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 7293 : 2019 Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)
ASTM D 1784 : 2020 Standard Classification System and Basis for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
ASTM F 3123 : 2022 Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN)
ASTM F 2818 : 2010 : R2019 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM F 2150 : 2019 Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Regenerative Medicine and Tissue-Engineered Medical Products
ASTM D 5721 : 2022 Standard Practice for Air-Oven Aging of Polyolefin Geomembranes
ASTM D 116 : 1986 : R2020 Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications
ASTM D 707 : 2015 Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)
ASTM F 1717 : 2021 Standard Test Methods for Spinal Implant Constructs in a Vertebrectomy Model
FC 3-260-18F:2023 Air Force Aircraft Arresting Systems Installation, Operation, And Maintenance, With Change 1

ASTM D 4066 : 2000 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 5947 : 1996 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4000 : 2013 Standard Classification System for Specifying Plastic Materials
ASTM E 1012 : 2014 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM E 83 : 2000 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM D 4000 : 2003 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2000 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 5947 : 2002 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4066 : 2001 : REV A : R2008 Standard Classification System for Nylon Injection and Extrusion Materials (PA) (Withdrawn 2012)
ASTM D 4000 : 2012 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 Standard Classification System for Specifying Plastic Materials
AS ISO/ASTM 52921:2020 Standard terminology for additive manufacturing - Coordinate systems and test methodologies
ASTM E 83 : 1998 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM D 4000 : 2011 Standard Classification System for Specifying Plastic Materials
ASTM D 5947 : 2011 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 5947 : 2018 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4066 : 2001 : REV A Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM E 1012 : 1999 Standard Practice for Verification of Specimen Alignment Under Tensile Loading
ASTM E 1012 : 2012 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM D 412 : 2016 : EDT 1 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D 4000 : 2004 : EDT 1 Standard Classification System for Specifying Plastic Materials
AS ISO/ASTM 52910:2020 Additive manufacturing - Design - Requirements, guidelines and recommendations
ASTM E 1012 : 2014 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4000 : 2009 : REV B Standard Classification System for Specifying Plastic Materials
ASTM D 4066 : 2013 : R2019 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 4000 : 2000 Standard Classification System for Specifying Plastic Materials
ASTM D 5947 : 2006 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4000 : 2010 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4066 : 2001 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 412 : 2016 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D 4000 : 2007 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 : REV A Standard Classification System for Specifying Plastic Materials
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 1012 : 2012 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM D 4000 : 2001 Standard Classification System for Specifying Plastic Materials
ASTM D 1822 : 2013 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ASTM D 1822 : 2006 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 4000 : 2008 Standard Classification System for Specifying Plastic Materials
ASTM D 4066 : 1994 : REV B Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 1822 : 1999 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ASTM E 1012 : 2005 Standard Practice for Verification of Test Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 5947 : 2003 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4000 : 2001 : REV A : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 1822 : 2021 Standard Test Method for Determining the Tensile-Impact Resistance of Plastics
ASTM D 5947 : 2001 : EDT 1 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4000 : 2004 Standard Classification System for Specifying Plastic Materials
ASTM D 412 : 2016 : R2021 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension
ASTM D 4066 : 2000 : REV A Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 4000 : 2010 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2003 Standard Classification System for Specifying Plastic Materials
ASTM E 1012 : 2019 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM D 4066 : 1996 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing

View more information
$135.86
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more