Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6419 : 2000 : R2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
Available format(s)

Hardcopy , PDF

Superseded date

18-08-2023

Language(s)

English

Published date

12-12-2017

CONTAINED IN VOL. 06.02, 2017 Defines a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks.

1.1This test method describes a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks. Test specimens are heated at 110° ± 1°C for 60 min.

Note 1:Coldset web offset printing is often (also) referred to as non-heatset web offset printing.

1.2This test method is also applicable to sheet-fed and coldset web offset printing ink vehicles.

Note 2:Vehicle is the liquid portion of the printing ink. Any substance that is dissolved in the liquid portion of the ink is a part of the vehicle.

1.3This test method is not applicable to ultra-violet (UV) or electron beam cured materials, which must be cured by exposure to UV light or an electron beam as part of the test for volatile content.

1.4This test method is based on Test Method D2369, in which the allowable ranges are ±0.1g for specimen weight and ±5°C for oven temperature. Interlaboratory studies have shown that specimen weight and oven temperature must both be more tightly controlled in order to improve the precision of test results for sheet-fed and coldset web-offset inks. Such inks typically contain a wide range of high-boiling hydrocarbons and often have a volatile content below 25 %.

1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement see 7.5.1

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 01
DocumentType
Test Method
Pages
3
ProductNote
Reconfirmed 2017
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7805 : 2013 : R2021 Standard Terminology for Printing Ink Vehicles and Related Materials
ASTM D 2369 : 2010 : R2015 : EDT 1 Standard Test Method for Volatile Content of Coatings
ASTM D 3960 : 2005 : R2018 Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
ASTM D 7805 : 2013 Standard Terminology for Printing Ink Vehicles and Related Materials

ASTM D 2369 : 1998 Standard Test Method for Volatile Content of Coatings
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2369 : 1981 : EDT 1 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 2001 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 2010 Standard Test Method for Volatile Content of Coatings
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2369 : 2020 Standard Test Method for Volatile Content of Coatings
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2369 : 2007 Standard Test Method for Volatile Content of Coatings
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2369 : 2010 : EDT 1 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 1993 Standard Test Method for Volatile Content of Coatings
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 2369 : 1995 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 2004 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 1990 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 2003 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 2010 : R2015 : EDT 1 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 1987 Standard Test Method for Volatile Content of Coatings
ASTM D 362 : 1984 Specification for Industrial Grade Toluene (Withdrawn 1989)
ASTM D 2369 : 2001 : EDT 1 Standard Test Method for Volatile Content of Coatings
ASTM D 2369 : 1992 Standard Test Method for Volatile Content of Coatings

View more information
$108.03
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more