ASTM D 6426 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
30-12-2022
English
14-02-2019
This test method covers a procedure for determining the filterability of distillate fuel oils within the viscosity range from 1.70 mm2/s to 6.20 mm2/s (cSt) at 40 °C.
1.1This test method covers a procedure for determining the filterability of distillate fuel oils within the viscosity range from 1.70 mm2/s to 6.20 mm2/s (cSt) at 40 °C.
Note 1:ASTM specification fuels falling within the scope of this test method are Specification D396 Grade No. 2, Specification D975 Grade No. 2-D, and Specification D2880 Grade No. 2-GT.
Note 2:The test method has been used with lower viscosity middle distillate fuels such as Specification D396 Grade No. 1, Specification D975 Grade No. 1-D, and Specification D2880 Grade No. 1-GT, but the precision has not been studied and therefore the stated precision has not been validated for these grades.
1.2This test method is not applicable to fuels that contain undissolved water.
1.3The values stated in SI units are to be regarded as standard.
1.3.1Non-SI units, specifically U.S. customary units such as temperature in degrees Fahrenheit and pressure in pounds per square inch gauge (psig), are included for information.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 6469 : 2017 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 2068 : 2017 | Standard Test Method for Determining Filter Blocking Tendency |
| ASTM D 7261 : 2017 | Standard Test Method for Determining Water Separation Characteristics of Diesel Fuels by Portable Separometer |
| ASTM D 6824 : 2013 : R2018 | Standard Test Method for Determining Filterability of Aviation Turbine Fuel |
| ASTM D 6974 : 2016 | Standard Practice for Enumeration of Viable Bacteria and Fungi in Liquid Fuels—Filtration and Culture Procedures |
| ASTM D 6824 : 2023 | Standard Test Method for Determining Filterability of Aviation Turbine Fuel |
| ASTM D 2068 : 2020 | Standard Test Method for Determining Filter Blocking Tendency |
| ASTM D 7261 : 2022 | Standard Test Method for Determining Water Separation Characteristics of Diesel Fuels by Portable Separometer |
| ASTM D 6469 : 2020 | Standard Guide for Microbial Contamination in Fuels and Fuel Systems |
| ASTM D 6974 : 2020 | Standard Practice for Enumeration of Viable Bacteria and Fungi in Liquid Fuels—Filtration and Culture Procedures |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4176 : 2021 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4057 : 1995 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4860 : 1991 : R1995 | Standard Test Method for Free Water and Particulate Contamination in Mid-Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4176 : 1993 : R1997 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4176 : 2004 : R2019 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 396 : 2020 | Standard Specification for Fuel Oils |
| ASTM D 975 : 2022 | Standard Specification for Diesel Fuel |
| ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4860 : 2008 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 396 : 1998 | Standard Specification for Fuel Oils |
| ASTM D 4860 : 2022 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 2880 : 2000 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 975 : 2019 : REV B | Standard Specification for Diesel Fuel |
| ASTM D 4860 : 2014 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 1990 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 975 : 2021 | Standard Specification for Diesel Fuel |
| ASTM D 2880 : 2013 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 2880 : 2013 : REV A | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4860 : 1991 : R2005 | Standard Test Method for Free Water and Particulate Contamination in Mid-Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 975 : 2020 : REV C | Standard Specification for Diesel Fuel |
| ASTM D 2880 : 2018 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4176 : 2004 : R2009 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 1998 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 2020 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4860 : 2021 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 2003 : R2010 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4176 : 2022 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4177 : 2022 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4176 : 2021 : REV A | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 2880 : 2015 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
| ASTM D 4176 : 2004 : R2014 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4176 : 2020 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4860 : 1991 : R2000 : EDT 1 | Standard Test Method for Free Water and Particulate Contamination in Mid-Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 975 : 2022 : REV A | Standard Specification for Diesel Fuel |
| ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
| ASTM D 396 : 2009 | Standard Specification for Fuel Oils |
| ASTM D 2880 : 2014 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4860 : 2014 : R2019 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 2013 : REV B | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 2020 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 1996 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4860 : 2013 | Standard Test Method for Free Water and Particulate Contamination in Middle Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 2880 : 2018 : REV A | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4176 : 2004 : EDT 1 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4176 : 2002 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 2880 : 1978 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4860 : 2007 | Standard Test Method for Free Water and Particulate Contamination in Mid-Distillate Fuels (Clear and Bright Numerical Rating) |
| ASTM D 2880 : 2003 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 4176 : 2004 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
| ASTM D 2880 : 2014 : REV A | Standard Specification for Gas Turbine Fuel Oils |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.