Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6750 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)
Available format(s)

Hardcopy , PDF

Superseded date

14-07-2023

Language(s)

English

Published date

06-06-2019

These test methods cover the performance of engine oils intended for use in certain diesel engines.

1.1These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % mass fuel sulfur) or 1N (0.04 % mass fuel sulfur) procedure.3 The only difference in the two test methods is the fuel used. Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D4485.

1.2These test methods, although based on the original Caterpillar 1K/1N procedures,3 also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see Annex A1 – Annex A4).

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3.1Exception—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or single source equipment specified. Also Brake Specific Fuel Consumption is measured in kilograms per kilowatthour.

1.4The following is the Table of Contents:

Section

Introduction

Scope

1

Referenced documents

2

Terminology

3

Summary of Test Methods

4

Significance and Use

5

Apparatus

6

General Laboratory Requirements

6.1

Test Engine

6.2

Test Engine Accessories and Parts

6.3

Reagents and Materials

7

Test Oil Sample Requirements

8

Preparation of Apparatus

9

Engine Inspection

9.1

Engine Pre-Test Lubrication System Flush

9.2

Engine Pre-Test Measurements and Inspections

9.3

Engine Assembly

9.4

Pressure Testing of Fuel System Assembly

9.5

Calibration of Engine Test Stand

10

General Requirements and Frequency of Calibration

10.1

Runs

10.2

Specified Test Parameters

10.3

Calibration Test Acceptance Criteria

10.4

Action on Rejection of Calibration Test

10.5

Test Numbering

10.6

Reference Oils

10.7

Severity Adjustments

10.8

Engine Operating Procedure

11

Engine Run-In

11.1

Cool-Down Procedure

11.2

Warm-Up Procedure

11.3

Operating Conditions and Oil Additions

11.4

Measurement of Oil Consumption

11.5

Sampling Used Oil

11.6

Shutdowns, Lost Time and Off Tolerance Conditions

11.7

Recording of Exhaust Temperature

11.8

Air-Fuel Ratio Measurement

11.9

Recording of Engine Conditions

11.10

Humidity Requirements/Calibration/Measurement

11.11

Inspections, Photographs and Measurements

12

Reference to Reporting Form

12.1

Pre-Test Measurements of Engine Parts

12.2

Post-Test Information

12.3

Oil Inspections

12.4

Report

13

General Directions

13.1

Electronic Transmission of Test Results (Optional)

13.12

Reporting Calibration Test Results

13.13

Precision and Bias

14

Keywords

15

ANNEXES

ASTM Test Monitoring Center Organization

Annex A1

ASTM Test Monitoring Center: Calibration Procedures

Annex A2

ASTM Test Monitoring Center: Maintenance Activities

Annex A3

ASTM Test Monitoring Center: Related Information

Annex A4

Specifications for Test Engine and Engine Build

Annex A5

Intake Air System Details

Annex A6

Exhaust System Details

Annex A7

Cooling System Details

Annex A8

Oil System Modifications and Instrument Locations

Annex A9

Other Pressure and Temperature Measurement Locations

Annex A10

Oil Consumption Linear Regression Method

Annex A11

Test Fuel Specifications

Annex A12

Lubrication System, Flush Apparatus and Procedure

Annex A13

Engine Operating Conditions

Annex A14

Procedure for Rating Piston and Liner

Annex A15

Calculation of Percent Offset and Percent Deviation

Annex A16

1K/1N Test Reporting

Annex A17

Parts List by Part Number (P/N) and Warranty

Annex A18

Safety Precautions

Annex A19

APPENDIXES

Humidity Data

Appendix X1

Statistical Equations for Mean and Standard Deviation

Appendix X2

Examples of Forms for Reporting

Appendix X3

Optional Recording of Oil Pass Limits

Appendix X4

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements appear throughout the text. Being engine tests, these test methods do have definite hazards that shall be met by safe practices (see Annex A19 on Safety Precautions).

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Test Method
Pages
70
ProductNote
THIS STANDARD ALSO REFERS TO ASTM D 2709
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7589 : 2016 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref >
ASTM D 4485 : 2020 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 6837 : 2013 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIB Spark Ignition Engine<rangeref></rangeref > (Withdrawn 2022)
ASTM D 6984 : 2018 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine
ASTM D 7320 : 2018 Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine

ASTM D 5862 : 2009 Standard Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine (Withdrawn 2009)
ASTM D 2425 : 2019 Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry
ASTM D 4485 : 2003 : REV A Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1992 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 7422 : 2012 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5844 : 1998 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Rusting (Sequence IID) (Withdrawn 2003)
ASTM D 4485 : 2006 Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1987 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 2709 : 1996 : R2011 : EDT 1 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 3524 : 2004 Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography (Withdrawn 2013)
ASTM D 2709 : 1996 : EDT 2 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4485 : 2011 : REV C Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 1319 : 1989 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption
ASTM D 1319 : 2008 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 1298 : 2012 : REV A Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 4485 : 2001 Standard Specification for Performance of Engine Oils
ASTM D 1796 : 2011 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 7422 : 2009 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 6202 : 2001 Standard Test Method for Automotive Engine Oils on the Fuel Economy of Passenger Cars and Light-Duty Trucks in the Sequence VIA Spark Ignition Engine
ASTM D 5185 : 1997 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM E 29 : 2013 : R2019 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 2425 : 2004 : R2009 Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry
ASTM D 4485 : 2003 Standard Specification for Performance of Engine Oils
ASTM D 6202 : 2000 : REV A Standard Test Method for Automotive Engine Oils on the Fuel Economy of Passenger Cars and Light-Duty Trucks in the Sequence VIA Spark Ignition Engine
ASTM D 4485 : 2008 Standard Specification for Performance of Engine Oils
ASTM D 4739 : 2005 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 2709 : 1996 : R2006 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 4485 : 2015 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 7422 : 2019 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 1298 : 2012 : REV B Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 3117 : 1996 : EDT 1 Standard Test Method for Wax Appearance Point of Distillate Fuels
ASTM D 1319 : 2018 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4485 : 2005 : REV A Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2016 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 6594 : 2013 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135  °C
ASTM D 2500 : 2016 : REV B Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 1319 : 2014 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4485 : 2011 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM E 29 : 2002 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM D 2622 : 1998 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2500 : 2016 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 2500 : 2016 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 1319 : 1999 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2015 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2018 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 5185 : 2005 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4737 : 2009 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 1298 : 1999 : R2005 Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 235 : 2022 Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
ASTM D 5185 : 2002 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 1298 : 2012 : REV B : R2017 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 1298 : 2012 Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 4485 : 2011 : REV B Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2622 : 2008 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4485 : 2016 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 4485 : 2007 Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2014 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2010 Standard Specification for Performance of Engine Oils
ASTM D 1298 : 1999 : EDT 2 Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 5185 : 2018 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4485 : 2001 : REV A Standard Specification for Performance of Engine Oils
ASTM D 7422 : 2010 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5186 : 2019 Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels By Supercritical Fluid Chromatography
ASTM D 7422 : 2008 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 1796 : 2004 : R2009 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 1319 : 2002 : REV A Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2017 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 2709 : 2016 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 2500 : 1999 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2002 : EDT 1 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 4739 : 2008 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 2500 : 2005 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 5185 : 2013 : EDT 1 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
ASTM D 5186 : 1999 Standard Test Method for Determination of Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels by Supercritical Fluid Chromatography
ASTM D 4485 : 2004 Standard Specification for Performance of Engine Oils
ASTM D 445 : 1988 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity)
ASTM D 1298 : 1999 Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 2500 : 2002 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 2500 : 2011 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 4739 : 2017 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 2500 : 2009 Standard Test Method for Cloud Point of Petroleum Products
ASTM D 6594 : 2020 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135 °C
ASTM D 3524 : 2014 Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography
ASTM D 4739 : 2006 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 1796 : 1997 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 4485 : 2000 Standard Specification for Performance of Engine Oils
ASTM D 4739 : 1996 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 2500 : 2017 Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 5186 : 2003 : R2009 Standard Test Method for Determination of Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels by Supercritical Fluid Chromatography
ASTM D 7422 : 2022 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 1319 : 2003 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2013 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2015 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 6594 : 2019 : REV A Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135 °C
ASTM D 5185 : 2013 Standard Test Method for Multielement Determination of Used and Unused Lubricating Oils and Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 6594 : 2014 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135°C
ASTM D 1796 : 1997 : EDT 1 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 664 : 1995 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
ASTM D 2622 : 2003 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2425 : 1999 Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry
ASTM D 1319 : 2010 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 4737 : 2009 : REV A Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 4737 : 2021 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 5186 : 2015 Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels By Supercritical Fluid Chromatography
ASTM D 2425 : 2021 Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry
ASTM D 7422 : 2015 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 1298 : 1999 : EDT 1 Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 4485 : 2006 : REV A Standard Specification for Performance of Engine Oils
ASTM D 4739 : 2011 : R2017 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4737 : 2010 : R2016 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 6594 : 2004 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135°C
ASTM D 2425 : 2004 Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry
ASTM D 445 : 2019 : REV A Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 7422 : 2016 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 2500 : 2017 : REV A Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels
ASTM D 7422 : 2011 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 7422 : 2010 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4737 : 2003 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 3524 : 1990 : R1999 Standard Test Method for Diesel Fuel Diluent in Used Diesel Engine Oils by Gas Chromatography
ASTM D 4739 : 2008 : EDT 1 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 235 : 2002 : R2012 Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) (Withdrawn 2021)
ASTM D 6594 : 2004 : REV A Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135°C
ASTM D 4485 : 2018 : REV A Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 3117 : 2003 Standard Test Method for Wax Appearance Point of Distillate Fuels (Withdrawn 2010)
ASTM D 2622 : 2010 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 6594 : 2006 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135°C
ASTM D 2709 : 1988 Standard Test Method for Water and Sediment in Distillate Fuels by Centrifuge
ASTM D 4485 : 2005 Standard Specification for Performance of Engine Oils
ASTM D 5185 : 2009 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 445 : 2001 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity)
ASTM D 4737 : 1996 : REV A Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 6202 : 2002 Standard Test Method for Automotive Engine Oils on the Fuel Economy of Passenger Cars and Light-Duty Trucks in the Sequence VIA Spark Ignition Engine (Withdrawn 2009)
ASTM D 2622 : 2021 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 445 : 2021 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 7422 : 2009 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 5186 : 2003 Standard Test Method for Determination of Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels and Aviation Turbine Fuels by Supercritical Fluid Chromatography
ASTM D 5862 : 2006 Standard Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine
ASTM D 6594 : 2001 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135<sup>o</sup>C
ASTM D 4485 : 2014 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
ASTM D 1796 : 2011 : R2016 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 4485 : 2002 Standard Specification for Performance of Engine Oils
ASTM D 5186 : 2022 Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels By Supercritical Fluid Chromatography
ASTM D 2622 : 2007 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 4485 : 2005 : EDT 1 Standard Specification for Performance of Engine Oils
ASTM D 2622 : 1994 Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry
ASTM D 5862 : 1999 : REV A Standard Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine
ASTM D 2622 : 2005 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 5185 : 2002 : EDT 1 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 5862 : 2003 Standard Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine
ASTM D 6594 : 2003 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135<sup>o</sup>C
ASTM D 6594 : 2000 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135<sup>o</sup>C
ASTM D 4737 : 2004 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 1298 : 1985 : R1990 : EDT 1 Standard Practice for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 1319 : 2015 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 7422 : 2017 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 1796 : 1997 : R2002 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 5185 : 2002 : EDT 2 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
ASTM D 4739 : 2011 Standard Test Method for Base Number Determination by Potentiometric Hydrochloric Acid Titration
ASTM D 4739 : 2002 Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 1319 : 2013 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 5186 : 1991 Standard Test Method for Determination of Aromatic Content of Diesel Fuels by Supercritical Fluid Chromatography
ASTM D 1796 : 2004 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 445 : 2021 : EDT 1 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 4739 : 2006 : REV A Standard Test Method for Base Number Determination by Potentiometric Titration
ASTM D 1796 : 2011 : EDT 1 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 1796 : 1983 : R1990 : EDT 1 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 2425 : 2017 Standard Test Method for Hydrocarbon Types in Middle Distillates by Mass Spectrometry
ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 4485 : 2009 Standard Specification for Performance of Engine Oils
ASTM D 4485 : 2019 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 6594 : 2005 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135°C
ASTM D 6594 : 2019 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135 °C
ASTM D 4485 : 2010 : REV A Standard Specification for Performance of Engine Oils
ASTM D 4485 : 2011 Standard Specification for Performance of Engine Oils
ASTM D 1319 : 2019 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 5186 : 2020 Standard Test Method for Determination of the Aromatic Content and Polynuclear Aromatic Content of Diesel Fuels By Supercritical Fluid Chromatography
ASTM D 4737 : 2010 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 6594 : 2008 Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135°C
ASTM D 1319 : 2002 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
ASTM D 2622 : 2016 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 2709 : 1996 : R2001 : EDT 1 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
ASTM D 7422 : 2014 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 4485 : 2007 : REV A Standard Specification for Performance of Engine Oils
ASTM E 29 : 2022 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

View more information
$204.61
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more