Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6779 : 2006

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

15-03-2006

1.1 This classification system covers polyamide materials suitable for molding and extrusion. Some of these compositions are also suitable for application from solution.

1.2 This classification system allows for the use of recycled polyamide materials provided that the requirements as stated in this classification system are met. The proportions of recycled material used, as well as the nature and amount of any contaminant, however, cannot be covered practically in this specification.

1.3 The properties included in this classification system are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section .

1.4 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system.

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

The following precautionary caveat pertains only to the test methods portion, Section , of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Note 1

This classification system is similar to ISO 1874-1/-2 , although the technical content is significantly different.

Committee
D 20
DocumentType
Standard
Pages
14
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
ASTM F 1733 : 2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
ASTM D 789 : 2018 Standard Test Method for Determination of Relative Viscosity of Concentrated Polyamide (PA) Solutions
ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 955 : 2008 : R2014 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
ASTM F 2807 : 2013 : R2018 Standard Specification for Multilayer Polyethylene-Polyamide (PE-PA) Pipe for Pressure Piping Applications
ASTM D 5628 : 2018 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass)
ASTM D 5740 : 2018 Standard Guide for Writing Material Standards in the Classification D4000 Format
ASTM D 5989 : 2018 Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA)
ASTM F 3091/F3091M : 2014 Standard Specification for Powder Bed Fusion of Plastic Materials
ASTM G 175 : 2013 Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications
ASTM F 2785 : 2018 : REV A Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
ASTM F 2600 : 2009 : R2018 Standard Specification for Electrofusion Type Polyamide-11 Fittings for Outside Diameter Controlled Polyamide-11 Pipe and Tubing

View more information
$135.86
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more