We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 7082 : 2015

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe

    Available format(s):  Hardcopy, PDF

    Superseded date:  24-05-2021

    Language(s):  English

    Published date:  05-11-2015

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This specification addresses the requirements for polyethylene stay in place forms for end walls or head walls for use with standard storm drainage systems.

    1.2The wall form system consists of a base wall form, a cap, an optional riser to adjust the height of the wall above the pipe, and an optional adaptor to adjust the pipe opening to accommodate smaller pipe sizes.

    1.3The form system is manufactured using the rotational molding process and is available in different colors.

    1.4The values stated in SI units are to be regarded as the standard, the inch-pounds in parentheses are given for information only.

    1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

    Note 1:There is no known ISO equivalent to this standard.

    General Product Information - (Show below) - (Hide below)

    Committee D 20
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 1238 : 2000 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 1238 : 2004 : REV C Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 1693 : 2000 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1238 : 2013 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 1238 : 2010 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 4883 : 2003 Standard Test Method for Density of Polyethylene by the Ultrasound Technique
    ASTM D 1693 : 2008 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1505 : 2003 Standard Test Method for Density of Plastics by the Density-Gradient Technique
    ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 1693 : 2015 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1693 : 2012 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1693 : 1994 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 1693 : 2005 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1238 : 2004 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 1505 : 1968 : R1979 Standard Test Method for Density Of Plastics By The Density-Gradient Technique
    ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics
    ASTM D 1693 : 2007 : REV A Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1505 : 2010 Standard Test Method for Density of Plastics by the Density-Gradient Technique
    ASTM D 1505 : 2018 Standard Test Method for Density of Plastics by the Density-Gradient Technique
    ASTM D 1505 : 1998 : EDT 1 Standard Test Method for Density of Plastics by the Density-Gradient Technique
    ASTM D 4883 : 2008 Standard Test Method for Density of Polyethylene by the Ultrasound Technique (Withdrawn 2017)
    ASTM D 1238 : 2001 : EDT 1 Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 4883 : 1999 Standard Test Method for Density of Polyethylene by the Ultrasound Technique
    ASTM D 1238 : 2004 : REV A Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 1693 : 2001 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1693 : 2013 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    ASTM D 1238 : 1985 Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer
    ASTM D 4883 : 2018 Standard Test Method for Density of Polyethylene by the Ultrasound Technique
    ASTM D 1693 : 2007 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective