ASTM D 7109 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
20-08-2020
English
01-06-2018
1.1 This test method covers the evaluation of the shearstability of polymer-containing fluids.
1.1This test method covers the evaluation of the shear stability of polymer-containing fluids. The test method measures the viscosity loss, in mm2/s and percent, at 100 °C of polymer-containing fluids when evaluated by a diesel injector apparatus procedure that uses European diesel injector test equipment. The viscosity loss reflects polymer degradation due to shear at the nozzle. Viscosity loss is evaluated after both 30 cycles and 90 cycles of shearing.
Note 1:This test method evaluates the shear stability of oils after both 30 cycles and 90 cycles of shearing. For most oils, there is a correlation between results after 30 cycles and results after 90 cycles of shearing, but this is not universal.
Note 2:Test Method D6278 uses essentially the same procedure with 30 cycles only instead of both 30 cycles and 90 cycles. The correlation between results from this test method at 30 cycles and results from Test Method D6278 has not been established.
Note 3:Test Method D2603 has been used for similar evaluation of shear stability; limitations are as indicated in the significance statement. No detailed attempt has been undertaken to correlate the results of this test method with those of the sonic shear test method.
Note 4:This test method uses test apparatus as defined in CEC L-14-A-93. This test method differs from CEC-L-14-A-93 in the period of time required for calibration.
Note 5:Test Method D5275 also shears oils in a diesel injector apparatus but may give different results.
Note 6:This test method has different calibration and operational requirements than withdrawn Test Method D3945.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific warning statements are given in Section 8.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 7156 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 6278 : 2017 : EDT 1 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 6022 : 2006 : R2012 | Standard Practice for Calculation of Permanent Shear Stability Index |
| ASTM D 7156 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
| ASTM D 6022 : 2019 | Standard Practice for Calculation of Permanent Shear Stability Index |
| ASTM D 2603 : 2019 | Standard Test Method for Sonic Shear Stability of Polymer-Containing Oils |
| ASTM D 6278 : 1998 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 6299 : 2010 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2013 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2017 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2017 : REV B | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2009 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 5275 : 2020 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
| ASTM D 6299 : 2013 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 2603 : 2001 : R2007 | Test Method for Sonic Shear Stability of Polymer-Containing Oils |
| ASTM D 6299 : 2010 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 2603 : 2019 | Standard Test Method for Sonic Shear Stability of Polymer-Containing Oils |
| ASTM D 6299 : 2000 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2010 : EDT 2 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2016 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2019 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2000 : REV A | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6278 : 2017 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 6299 : 2020 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 2603 : 1998 | Test Method for Sonic Shear Stability of Polymer-Containing Oils |
| ASTM D 6278 : 2017 : EDT 1 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 2603 : 2001 : R2013 | Standard Test Method for Sonic Shear Stability of Polymer-Containing Oils |
| ASTM D 6299 : 2008 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6278 : 2012 : EDT 1 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 5275 : 2011 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
| ASTM D 6299 : 2002 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 2603 : 2001 | Test Method for Sonic Shear Stability of Polymer-Containing Oils |
| ASTM D 2603 : 2020 | Standard Test Method for Sonic Shear Stability of Polymer-Containing Oils |
| ASTM D 5275 : 1992 : R1998 : EDT 1 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
| ASTM D 5275 : 2003 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
| ASTM D 5275 : 2016 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
| ASTM D 6299 : 2007 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2007 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6278 : 2002 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 5275 : 2017 | Standard Test Method for Fuel Injector Shear Stability Test (FISST) for Polymer Containing Fluids |
| ASTM D 6278 : 2007 | Standard Test Method for Shear Stability of Polymer Containing Fluids Using a European Diesel Injector Apparatus |
| ASTM D 6299 : 2017 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2002 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.