Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

ASTM D 7175 : 2015 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
Available format(s)

PDF

Superseded date

30-01-2024

Language(s)

English

Published date

05-08-2015

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 04.03, 2015 Defines the determination of the dynamic shear modulus and phase angle of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry.

1.1This test method covers the determination of the dynamic shear modulus and phase angle of asphalt binders when tested in dynamic (oscillatory) shear using parallel plate geometry. It is applicable to asphalt binders having dynamic shear modulus values in the range from 100 Pa to 10 MPa. This range in modulus is typically obtained between 4 and 88°C at 10 rad/s. This test method is intended for determining the linear viscoelastic properties of asphalt binders as required for specification testing and is not intended as a comprehensive procedure for the full characterization of the viscoelastic properties of asphalt binders.

1.2This standard is appropriate for unaged materials, material aged in accordance with Test Method D2872, material aged in accordance with Practice D6521, or material aged in accordance with both Test Method D2872 and Practice D6521. This procedure is limited to asphalt binders that contain particles with largest dimension less than 250 μm.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 04
DocumentType
Redline
Pages
16
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 7405 : 2015 : REDLINE Standard Test Method for Multiple Stress Creep and Recovery (MSCR) of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM D 7654/D7654M : 2010 Standard Specification for Asphalt Used in Roofing Measured by Dynamic Shear Rheometer
ASTM D 7173 : 2014 : REDLINE Standard Practice for Determining the Separation Tendency of Polymer from Polymer Modified Asphalt
ASTM D 7552 : 2009 Standard Test Method for Determining the Complex Shear Modulus (G*) Of Bituminous Mixtures Using Dynamic Shear Rheometer
ASTM D 7944 : 2015 Standard Practice for Recovery of Emulsified Asphalt Residue Using a Vacuum Oven
ASTM D 7643 : 2016 : REDLINE Standard Practice for Determining the Continuous Grading Temperatures and Continuous Grades for PG Graded Asphalt Binders
ASTM D 6626 : 2015 : REDLINE Standard Specification for Performance Graded Trinidad Lake Modified Asphalt Binder
ASTM D 6373 : 2016 : REDLINE Standard Specification for Performance Graded Asphalt Binder
ASTM D 4887/D4887M : 2011 : R2016 Standard Practice for Preparation of Viscosity Blends for Hot Recycled Asphalt Materials
ASTM D 2493/D2493M : 2016 : REDLINE Standard Practice for Viscosity-Temperature Chart for Asphalt Binders
ASTM D 7552 : 2009 : R2014 Standard Test Method for Determining the Complex Shear Modulus (G*) Of Bituminous Mixtures Using Dynamic Shear Rheometer
ASTM D 4887/D4887M : 2011 Standard Practice for Preparation of Viscosity Blends for Hot Recycled Bituminous Materials

DIN 43760:1987-09 MEASUREMENT AND CONTROL - ELECTRICAL TEMPERATURE SENSORS - REFERENCES-TABLES FOR NICKEL RESISTORS FOR RESISTANCE THERMOMETERS
ASTM E 644 : 2011 : REDLINE Standard Test Methods for Testing Industrial Resistance Thermometers
AASHTO R 29 : 2015 PRACTICE FOR GRADING OR VERIFYING THE PERFORMANCE GRADE (PG) OF AN ASPHALT BINDER
AASHTO T 315 : 2012 METHOD OF TEST FOR DETERMINING THE RHEOLOGICAL PROPERTIES OF ASPHALT BINDER USING A DYNAMIC SHEAR RHEOMETER (DSR)
ASTM C 670 : 2015 : REDLINE Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
ASTM D 6373 : 2016 : REDLINE Standard Specification for Performance Graded Asphalt Binder

View more information
$135.86
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more