ASTM D 7209 : 2006
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
Available format(s)
Hardcopy , PDF
Withdrawn date
31-01-2015
Language(s)
English
Published date
15-01-2006
CONTAINED IN VOL. 08.03, 2014 Provides information for the development of standards (guides, practices, terminology, test methods, or specifications) relating to plastics recycling and other means of waste reductions and resource recovery.
1.1 This guide provides information for the development of standards (guides, practices, terminology, test methods, or specifications) relating to plastics recycling and other means of waste reductions and resource recovery.
1.2 This guide is directed to consumer, commercial, and industrial sources of thermoplastics and thermoset polymeric materials.
1.3 This guide addresses terminology, performance standards, specifications, quality assurance, separation or segregation of product by classes, identification and marking of generic classes, contaminants, fillers, designing for recycle, degradable products, reconstituted products, biobased resins, certification and percentages of recycled products, and other methods of waste reduction and resource recovery.
1.4 This guide does not address parameters or factors involving the original manufacture of virgin polymers or the fabrication of consumer products from these virgin polymers.
1.5 This guide is intended to replace Guide D 5033.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1There is no equivalent ISO standard. ISO/DIS 15270 is similar in scope and content.
| Committee |
D 20
|
| DevelopmentNote |
Supersedes ASTM D 5033. (12/2007)
|
| DocumentType |
Guide
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Withdrawn
|
| ASTM D 707 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| ASTM D 5047 : 2017 : REDLINE | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| NF ISO 15270 : 2009 | PLASTICS - GUIDELINES FOR THE RECOVERY AND RECYCLING OF PLASTICS WASTE |
| ASTM D 7293 : 2012 : REDLINE | Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI) |
| ASTM D 1248 : 2016 : REDLINE | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 5998 : 2016 : REDLINE | Standard Specification for Molded Polyethylene Shipping and Storage Drums |
| ASTM D 2103 : 2015 : REDLINE | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 6779 : 2017 : REDLINE | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 3981 : 2009 : REV A : R2016 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 6778 : 2014 : REDLINE | Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) |
| ASTM D 1562 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM D 7793 : 2017 : REDLINE | Standard Specification for Insulated Vinyl Siding |
| ASTM D 6713 : 2014 : REDLINE | Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) |
| (INACTIVE RECORD)ASTM D 5336 : 2015-04 | CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPHTHALAMIDE (PPA) INJECTION MOLDING MATERIALS |
| ASTM D 4801 : 2008 | Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm [0.010 in.] and Greater |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7436 : 2017 : REDLINE | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM D 6262 : 2017 : REDLINE | Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) |
| ASTM D 3935 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
| ASTM D 6457 : 2008 : R2013 | Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE) (Withdrawn 2018) |
| ASTM D 6394 : 2014 : REDLINE | Standard Specification for Sulfone Plastics (SP) |
| 17/30333280 DC : 0 | BS ISO 17422 - PLASTICS - ENVIRONMENTAL ASPECTS - GENERAL GUIDELINES FOR THEIR INCLUSION IN STANDARDS |
| ASTM D 5926 : 2015 : REDLINE | Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems |
| ASTM D 6100 : 2017 : REDLINE | Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM) |
| ASTM D 6778 : 2014 | Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) |
| ASTM D 6779 : 2017 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 5336 : 2015 : REV A | Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material |
| ASTM D 4634 : 2016 | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
| ASTM D 5927 : 2017 | Standard Classification System for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods |
| ASTM D 7445 : 2018 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
| ASTM D 5491 : 2008 : R2014 | Standard Classification for Recycled Post-Consumer Polyethylene Film Sources for Molding and Extrusion Materials |
| ASTM D 4068 : 2017 | Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane |
| ASTM D 706 : 2015 | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM D 5998 : 2016 | Standard Specification for Molded Polyethylene Shipping and Storage Drums |
| ASTM D 7793 : 2017 | Standard Specification for Insulated Vinyl Siding |
| ASTM D 5205 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ISO 15270:2008 | Plastics — Guidelines for the recovery and recycling of plastics waste |
| ASTM D 6358 : 2019 : EDT 1 | Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods |
| ASTM D 4101 : 2017 : EDT 1 | Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials |
| ASTM D 5675 : 2013 : R2018 | Standard Classification for Low Molecular Weight PTFE and FEP Micronized Powders |
| ASTM D 5857 : 2017 : REDLINE | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
| ASTM D 6261 : 2014 : REDLINE | Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES) |
| ASTM D 3981 : 2009 : REV A | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 5927 : 2017 : REDLINE | Standard Classification System for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods |
| ASTM D 5989 : 2018 | Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA) |
| ASTM D 1562 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM D 1710 : 2015 | Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes |
| ASTM D 8195 : 2018 | Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 5740 : 2018 | Standard Guide for Writing Material Standards in the Classification D4000 Format |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6100 : 2017 | Standard Specification for Extruded, Compression Molded and Injection Molded Polyoxymethylene Shapes (POM) |
| ASTM D 6713 : 2014 | Standard Specification for Extruded and Compression Molded Shapes Made from Poly(Vinylidene Fluoride) (PVDF) |
| ASTM D 3678 : 2014 | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions |
| ASTM D 7292 : 2018 | Standard Specification for Extruded, Compression-Molded, and Injection-Molded Basic Shapes of Polyamide-Imide (PAI) |
| ASTM D 5926 : 2015 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems |
| ASTM D 5857 : 2017 | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
| ASTM D 7436 : 2017 | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM D 5138 : 2016 | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM D 6262 : 2017 | Standard Specification for Extruded, Compression Molded, and Injection Molded Basic Shapes of Poly(aryl ether ketone) (PAEK) |
| ASTM D 707 : 2015 | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 3935 : 2015 | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
| ASTM D 7293 : 2012 | Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI) |
| ASTM D 5205 : 2016 | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 6394 : 2014 | Standard Specification for Sulfone Plastics (SP) |
| ASTM D 6261 : 2014 | Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES) |
| ASTM D 4976 : 2012 : REV A | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials |
| ASTM D 5047 : 2017 | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 6263 : 2015 | Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) |
| ASTM D 1248 : 2016 | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM D 4634 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA) |
| ASTM D 6263 : 2015 : REDLINE | Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) |
| ASTM D 4801 : 2008 : R2016 | Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater |
| ASTM D 3678 : 2014 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions |
| ASTM D 6457 : 2008 | Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE) |
| ASTM D 5138 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM D 4635 : 2016 : REDLINE | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 4068 : 2017 : REDLINE | Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane |
| ASTM D 706 : 2015 : REDLINE | Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA) |
| ASTM D 7445 : 2018 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding) |
| ASTM D 3981 : 2009 | Standard Specification for Polyethylene Films Made from Medium-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 1710 : 2015 : REDLINE | Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes |
| ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
| CFR 16(PTS0-999) : 0 | COMMERCIAL PRACTICES |
| ASTM D 2665 : 2014 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.