We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ASTM D 7293 : 2012

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)

    Available format(s):  Hardcopy, PDF

    Superseded date:  29-08-2019

    Language(s):  English

    Published date:  01-08-2012

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1This specification covers requirements and test methods for the dimensions, workmanship, and the properties of extruded and compression-molded sheet, plate, rod and tubular bar manufactured from polyetherimide (PEI) resins.

    1.2The properties included in this specification are those required for the compositions covered. It is possible that other requirements will be necessary to identify particular characteristics important to specialized applications. These shall be specified by using the suffixes as given in Section 5.

    1.3This specification does not allow for the use of recycled plastics (as defined in Guide D7209).

    1.4The values stated in English units are regarded as standard in all property and dimensional tables. For reference purposes, SI units are also included in Table 1 and Table S-PEI.

    1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1There is no known ISO equivalent to this standard.

    General Product Information - (Show below) - (Hide below)

    Committee D 20
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 5205 : 1996 Standard Classification System for Polyetherimide (PEI) Materials
    ASTM D 4000 : 2013 Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2003 : REV A Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2000 : REV A Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2012 Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2009 Standard Classification System for Specifying Plastic Materials
    ASTM D 3892 : 1993 : R2003 Standard Practice for Packaging/Packing of Plastics
    ASTM D 4000 : 2011 Standard Classification System for Specifying Plastic Materials
    ASTM D 7209 : 2006 Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
    ASTM D 3892 : 1993 : R1998 Standard Practice for Packaging/Packing of Plastics
    ASTM D 4000 : 2004 : EDT 1 Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2009 : REV B Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2000 Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2010 : REV A Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2007 Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2009 : REV A Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2001 Standard Classification System for Specifying Plastic Materials
    ASTM D 5205 : 2016 Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
    ASTM D 4000 : 2008 Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2001 : REV A : EDT 1 Standard Classification System for Specifying Plastic Materials
    ASTM D 5205 : 2010 Standard Classification System for Polyetherimide (PEI) Materials
    ASTM D 4000 : 2004 Standard Classification System for Specifying Plastic Materials
    ASTM D 3892 : 1993 : R2009 Standard Practice for Packaging/Packing of Plastics
    ASTM D 4000 : 2010 Standard Classification System for Specifying Plastic Materials
    ASTM D 4000 : 2003 Standard Classification System for Specifying Plastic Materials
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective